Machinability enhancement of heat-treated Incoloy 800H during turning using laser-textured carbide inserts under semi-solid MoS₂ lubrication
PLOS One · 2026
DOI: 10.1371/journal.pone.0349106 ↗Kurz gefasst
Fachartikel in der Zeitschrift PLOS One, 2026. Verfasst von Palanisamy Angappan und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Surya Engineering College, Erode, Tamil Nadu, India. Hauptthemen laut MEDLINE: Molybdenum, Hot Temperature, Lasers, Tungsten Compounds. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Incoloy 800H is an iron–nickel–chromium based superalloy widely used in high-temperature applications, but its poor machinability due to rapid work hardening and low thermal conductivity makes machining difficult. This study experimentally investigates the machinability of heat-treated Incoloy 800H during CNC turning using laser-textured tungsten carbide cutting inserts combined with semi-solid MoS₂ lubrication. Four tool configurations were examined: non-textured (NT), parallel-textured (PT), elliptical-textured (ET), and semi-elliptical-textured (SCT) inserts. Turning experiments were performed by varying cutting speed (35–55 m/min) and feed rate (0.02–0.06 mm/rev) while maintaining a constant depth of cut of 1 mm. Machining performance was evaluated through surface roughness, cutting force, cutting power, specific energy consumption, specific cutting pressure, tool-tip temperature, and material removal rate. The results indicate that the parallel-textured tool exhibited superior machining performance compared with the other inserts. The lowest surface roughness of 0.30 µm, cutting force of 91.23 N, and tool-tip temperature of 73.2 °C were obtained with the PT insert under optimal cutting conditions. The improved performance is attributed to reduced tool–chip contact length and enhanced lubrication at the interface provided by the textured surface combined with MoS₂ lubrication. Scanning electron microscopy and energy-dispersive X-ray analysis confirmed diffusion and abrasion as the dominant tool wear mechanisms. The findings demonstrate that the combined application of laser surface texturing and semi-solid MoS₂ lubrication significantly improves the machinability of Incoloy 800H during turning operations. The study provides experimental evidence that parallel-oriented surface textures effectively reduce tool–chip contact length and frictional interaction, thereby enhancing machining performance for difficult-to-cut superalloys.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Department of Mechanical Engineering, Surya Engineering College, Erode, Tamil Nadu, India.
- Department of Mechanical Engineering, Adhi College of Engineering and Technology, Kancheepuram, Tamil Nadu, India.
- Department of Mechanical Engineering, Roever Engineering College, Perambalur, Tamil Nadu, India.
- Department of Mechanical Engineering, College of Science and Technology, Royal University of Bhutan, Phuentsholing, Bhutan.
- Department of Mechanical Engineering, K. Ramakrishnan College of Engineering, Tiruchirappalli, Tamil Nadu, India.
ORCID-Profile: Abhishek Agarwal
Zitieren
APA
Angappan, P., Duraisamy, P., Chellamuthu, P., Agarwal, A., & Kasirajan, L. (2026). Machinability enhancement of heat-treated Incoloy 800H during turning using laser-textured carbide inserts under semi-solid MoS₂ lubrication. PLOS One. https://doi.org/10.1371/journal.pone.0349106
Vancouver
Angappan P, Duraisamy P, Chellamuthu P, Agarwal A, Kasirajan L. Machinability enhancement of heat-treated Incoloy 800H during turning using laser-textured carbide inserts under semi-solid MoS₂ lubrication. PLOS One. 2026. doi:10.1371/journal.pone.0349106
BibTeX
@article{Angappan2026,
author = {Angappan, Palanisamy and Duraisamy, Palanisamy and Chellamuthu, Prakash and Agarwal, Abhishek and Kasirajan, Lenin},
title = {Machinability enhancement of heat-treated Incoloy 800H during turning using laser-textured carbide inserts under semi-solid MoS₂ lubrication},
journal = {PLOS One},
year = {2026},
doi = {10.1371/journal.pone.0349106}
}
EUVIMED