EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

An integrated method for lightweight design and additive manufacturing of UAV arms

Ruoyu Wang, Wenwei Yang iD, Guoying Pang, Zhiru Liu, Xue Rao, Yangyang Yu

PLOS One · 11.03.2026 · 21 (3) · e0344000

DOI: 10.1371/journal.pone.0344000 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS One, online erschienen am 11.03.2026. Verfasst von Ruoyu Wang und 5 weiteren Autor:innen. Beteiligte Einrichtung: School of Intelligent Media and Design Art, Tianjin Renai College, Tianjin, China. Hauptthemen laut MEDLINE: Unmanned Aerial Devices, Equipment Design. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: China Postdoctoral Science Foundation, the Foundation of National Key Laboratory of Vehicle Power System, Tianjin Research Innovation Project for Postgraduate Students.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Topology optimization and additive manufacturing (AM) have been widely applied to the lightweight design and fabrication of unmanned aerial vehicles (UAVs). However, existing topology optimization methods for UAVs typically assume isotropic materials, neglecting the anisotropy inherent in AM and the associated manufacturing precision constraints. This paper proposes a lightweight integrated method in MATLAB R2021a for the design and AM of UAV arms that simultaneously accounts for printing-induced anisotropy and minimum feature size constraints. A topology optimization model is proposed that uses nodal density and element printing angle as coupled design variables, and the corresponding sensitivity analysis is carried out. In the manufacturing phase, a contour-offset strategy is employed to generate printing paths for the optimized structures, achieving effective force transmission. The effects of manufacturing and optimization parameters on the design results are systematically investigated. The results show that, compared with the traditional optimization method, the compliance difference between the optimized structure obtained by the proposed method and the traditional method is only 0.46%. Furthermore, while ensuring manufacturability, printing efficiency is improved by approximately 69%. This approach establishes a unified design-to-manufacturing workflow, providing both a theoretical foundation and a practical pathway for the intelligent design and efficient fabrication of UAVs and other lightweight structural components.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Unmanned Aerial DevicesEquipment DesignPrinting, Three-DimensionalComputer-Aided DesignModels, TheoreticalAlgorithmsAnisotropy

Autor:innen und Institutionen

  • School of Intelligent Media and Design Art, Tianjin Renai College, Tianjin, China.
  • School of Mechanical and Power Engineering, Tianjin Renai College, Tianjin, China.
  • State Key Laboratory of Engine, Tianjin University, Tianjin, China.

ORCID-Profile: Wenwei Yang

Förderung

  • China Postdoctoral Science Foundation
  • the Foundation of National Key Laboratory of Vehicle Power System
  • Tianjin Research Innovation Project for Postgraduate Students
  • Natural Science Foundation of Tianjin Municipality

Zitieren

APA

Wang, R., Yang, W., Pang, G., Liu, Z., Rao, X., & Yu, Y. (2026). An integrated method for lightweight design and additive manufacturing of UAV arms. PLOS One, 21(3), e0344000. https://doi.org/10.1371/journal.pone.0344000

Vancouver

Wang R, Yang W, Pang G, Liu Z, Rao X, Yu Y. An integrated method for lightweight design and additive manufacturing of UAV arms. PLOS One. 2026;21(3):e0344000. doi:10.1371/journal.pone.0344000

BibTeX
@article{Wang2026,
  author = {Wang, Ruoyu and Yang, Wenwei and Pang, Guoying and Liu, Zhiru and Rao, Xue and Yu, Yangyang},
  title = {An integrated method for lightweight design and additive manufacturing of UAV arms},
  journal = {PLOS One},
  year = {2026},
  volume = {21},
  number = {3},
  pages = {e0344000},
  doi = {10.1371/journal.pone.0344000}
}
Kostenlos starten →