EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Impact of the dimple indentation depth and location for passive flow control in Blended Wing Body airframe at low and high subsonic speeds

Haris Ali iD, Mohammad Rasidi Rasani iD, Zambri Harun

PLOS One · 2025

DOI: 10.1371/journal.pone.0325778 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS One, 2025. Verfasst von Haris Ali und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical and Manufacturing Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia (UKM), Bangi, Se…. Hauptthemen laut MEDLINE: Wings, Animal, Flight, Animal. Die Arbeit nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Universiti Kebangsaan Malaysia.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This research investigates the role of dimples in enhancing the aerodynamic characteristics of a Blended-Wing-Body (BWB) airframe. Numerical simulations, grounded in Computational Fluid Dynamics (CFD), were utilized to model turbulent airflow and assess the aerodynamic forces acting on the wing structure. The k-ω Shear-Stress Transport (SST) turbulence model was applied to effectively solve the governing equations. The impact of four dimple indentation depths ( d/D d = 0.025, 0.05, 0.075, and 0.1) at six specific locations on either the suction or pressure sides of the BWB wing surface was investigated. Simulations were performed at Mach 0.15 and Mach 0.6, treating the flow as incompressible and compressible, respectively, to capture variations in aerodynamic behavior. The evaluation involved analyzing the drag coefficient ( C D ), lift coefficient ( C L ), and lift-to-drag ( L/D ) ratio. The results reveal that, under optimal conditions, a dimpled BWB surface can achieve a reduction in C D by as much as 4.09% relative to a non-modified surface, without negatively impacting lift. This improvement is primarily due to the dimples’ capacity to maintain attached flow and postpone flow separation. Implementing dimples on the BWB wing surface as a passive flow control method has proven effective in enhancing the aerodynamic efficiency of lifting surfaces.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Wings, AnimalFlight, AnimalHydrodynamicsAnimalsComputer SimulationBiomechanical Phenomena

Autor:innen und Institutionen

  • Department of Mechanical and Manufacturing Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia (UKM), Bangi, Selangor, Malaysia.

ORCID-Profile: Haris Ali, Mohammad Rasidi Rasani

Förderung

  • Universiti Kebangsaan Malaysia

Zitieren

APA

Ali, H., Rasani, M. R., & Harun, Z. (2025). Impact of the dimple indentation depth and location for passive flow control in Blended Wing Body airframe at low and high subsonic speeds. PLOS One. https://doi.org/10.1371/journal.pone.0325778

Vancouver

Ali H, Rasani MR, Harun Z. Impact of the dimple indentation depth and location for passive flow control in Blended Wing Body airframe at low and high subsonic speeds. PLOS One. 2025. doi:10.1371/journal.pone.0325778

BibTeX
@article{Ali2025,
  author = {Ali, Haris and Rasani, Mohammad Rasidi and Harun, Zambri},
  title = {Impact of the dimple indentation depth and location for passive flow control in Blended Wing Body airframe at low and high subsonic speeds},
  journal = {PLOS One},
  year = {2025},
  doi = {10.1371/journal.pone.0325778}
}
Kostenlos starten →