EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Development of low-cost micro-fabrication procedures for planar micro-thermoelectric generators based on thin-film technology for energy harvesting applications

Sobhy M Abdelkader, Donart Nayebare iD, Tamer F Megahed, Ahmed M R Fath El-Bab, Mohamed A Ismeil iD, Omar Abdel-Rahim iD

PLOS ONE · 2024

DOI: 10.1371/journal.pone.0306540 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS ONE, 2024. Verfasst von Sobhy M Abdelkader und 5 weiteren Autor:innen. Beteiligte Einrichtung: Electrical Power Engineering, Egypt-Japan University of Science and Technology (E-JUST), Alexandria, Egypt. Hauptthemen laut MEDLINE: Electric Power Supplies. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deanship of Scientific Research at King Khalid University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

With the rapid proliferation of portable and wearable electronics, energy autonomy through efficient energy harvesting has become paramount. Thermoelectric generators (TEGs) stand out as promising candidates due to their silent operation, high reliability, and maintenance-free nature. This paper presents the design, fabrication, and analysis of a micro-scale TEG for powering such devices. A planar configuration was employed for its inherent miniaturization advantages. Finite element analysis using ANSYS reveals that a double-layer device under a 50 K temperature gradient generates an impressive open-circuit voltage of 1417 mV and a power output of 2.4 μW, significantly exceeding its single-layer counterpart (226 mV, 0.12 μW). Validation against the analytical model results yields errors within 2.44% and 2.03% for voltage and power, respectively. Furthermore, a single-layer prototype fabricated using paper shadow masks and sputtering deposition exhibits a voltage of 131 mV for a 50 K temperature difference, thus confirming the feasibility of the proposed design. This work establishes a foundation for developing highly efficient micro-TEGs for powering next-generation portable and wearable electronics.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Electric Power SuppliesWearable Electronic DevicesTemperatureEquipment DesignFinite Element AnalysisMiniaturizationElectricity

Autor:innen und Institutionen

  • Electrical Power Engineering, Egypt-Japan University of Science and Technology (E-JUST), Alexandria, Egypt.
  • Electrical Engineering Department, Faculty of Engineering, Mansoura University, Mansoura, Egypt.
  • Mechatronics and Robotics Engineering Department, Egypt-Japan University of Science and Technology (E-JUST), Alexandria, Egypt.
  • Electrical Engineering Department, Faculty of Engineering, King Khalid University, Abha, Saudi Arabia.
  • Electrical Engineering Department, Faculty of Engineering, Aswan University, Aswan, Egypt.

ORCID-Profile: Donart Nayebare, Mohamed A Ismeil, Omar Abdel-Rahim

Förderung

  • Deanship of Scientific Research at King Khalid University

Zitieren

APA

Abdelkader, S. M., Nayebare, D., Megahed, T. F., El-Bab, A. M. R. F., Ismeil, M. A., & Abdel-Rahim, O. (2024). Development of low-cost micro-fabrication procedures for planar micro-thermoelectric generators based on thin-film technology for energy harvesting applications. PLOS ONE. https://doi.org/10.1371/journal.pone.0306540

Vancouver

Abdelkader SM, Nayebare D, Megahed TF, El-Bab AMRF, Ismeil MA, Abdel-Rahim O. Development of low-cost micro-fabrication procedures for planar micro-thermoelectric generators based on thin-film technology for energy harvesting applications. PLOS ONE. 2024. doi:10.1371/journal.pone.0306540

BibTeX
@article{Abdelkader2024,
  author = {Abdelkader, Sobhy M and Nayebare, Donart and Megahed, Tamer F and El-Bab, Ahmed M R Fath and Ismeil, Mohamed A and Abdel-Rahim, Omar},
  title = {Development of low-cost micro-fabrication procedures for planar micro-thermoelectric generators based on thin-film technology for energy harvesting applications},
  journal = {PLOS ONE},
  year = {2024},
  doi = {10.1371/journal.pone.0306540}
}
Kostenlos starten →