EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Development of a low-cost robotized 3D-prototype for automated optical microscopy diagnosis: An open-source system

Allisson Dantas de Oliveira iD, Carles Rubio Maturana iD, Francesc Zarzuela Serrat, Bruno Motta Carvalho, Elena Sulleiro, Clara Prats iD, Anna Veiga, Mercedes Bosch, Javier Zulueta, Alberto Abelló, Elisa Sayrol, Joan Joseph-Munné und 1 weitere

PLOS ONE · 2024

DOI: 10.1371/journal.pone.0304085 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS ONE, 2024. Verfasst von Allisson Dantas de Oliveira und 12 weiteren Autor:innen. Beteiligte Einrichtung: Computational Biology and Complex Systems Group, Physics Department, Universitat Politècnica de Catalunya (UPC), Castelldefels, Spain. Hauptthemen laut MEDLINE: Microscopy. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In a clinical context, conventional optical microscopy is commonly used for the visualization of biological samples for diagnosis. However, the availability of molecular techniques and rapid diagnostic tests are reducing the use of conventional microscopy, and consequently the number of experienced professionals starts to decrease. Moreover, the continuous visualization during long periods of time through an optical microscope could affect the final diagnosis results due to induced human errors and fatigue. Therefore, microscopy automation is a challenge to be achieved and address this problem. The aim of the study is to develop a low-cost automated system for the visualization of microbiological/parasitological samples by using a conventional optical microscope, and specially designed for its implementation in resource-poor settings laboratories. A 3D-prototype to automate the majority of conventional optical microscopes was designed. Pieces were built with 3D-printing technology and polylactic acid biodegradable material with Tinkercad/Ultimaker Cura 5.1 slicing softwares. The system’s components were divided into three subgroups: microscope stage pieces, storage/autofocus-pieces, and smartphone pieces. The prototype is based on servo motors, controlled by Arduino open-source electronic platform, to emulate the X-Y and auto-focus (Z) movements of the microscope. An average time of 27.00 ± 2.58 seconds is required to auto-focus a single FoV. Auto-focus evaluation demonstrates a mean average maximum Laplacian value of 11.83 with tested images. The whole automation process is controlled by a smartphone device, which is responsible for acquiring images for further diagnosis via convolutional neural networks. The prototype is specially designed for resource-poor settings, where microscopy diagnosis is still a routine process. The coalescence between convolutional neural network predictive models and the automation of the movements of a conventional optical microscope confer the system a wide range of image-based diagnosis applications. The accessibility of the system could help improve diagnostics and provide new tools to laboratories worldwide.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

MicroscopyHumansPrinting, Three-DimensionalSoftwareRoboticsSmartphoneAutomationImaging, Three-Dimensional

Autor:innen und Institutionen

  • Computational Biology and Complex Systems Group, Physics Department, Universitat Politècnica de Catalunya (UPC), Castelldefels, Spain.
  • Microbiology Department, Vall d'Hebron Research Institute (VHIR), Vall d'Hebron University Hospital, Barcelona, Spain.
  • Department of Microbiology and Genetics, Universitat Autònoma de Barcelona (UAB), Barcelona, Spain.
  • Department of Informatics and Applied Mathematics, Federal University of Rio Grande do Norte, Natal, Brazil.
  • CIBERINFEC, ISCIII- CIBER de Enfermedades Infecciosas, Instituto de Salud Carlos III, Madrid, Spain.
  • Probitas Foundation, Barcelona, Spain.

ORCID-Profile: Allisson Dantas de Oliveira, Carles Rubio Maturana, Clara Prats

Zitieren

APA

Dantas de Oliveira, A., Rubio Maturana, C., Zarzuela Serrat, F., Carvalho, B. M., Sulleiro, E., Prats, C., Veiga, A., Bosch, M., Zulueta, J., Abelló, A., Sayrol, E., Joseph-Munné, J., & López-Codina, D. (2024). Development of a low-cost robotized 3D-prototype for automated optical microscopy diagnosis: An open-source system. PLOS ONE. https://doi.org/10.1371/journal.pone.0304085

Vancouver

Dantas de Oliveira A, Rubio Maturana C, Zarzuela Serrat F, Carvalho BM, Sulleiro E, Prats C, et al. Development of a low-cost robotized 3D-prototype for automated optical microscopy diagnosis: An open-source system. PLOS ONE. 2024. doi:10.1371/journal.pone.0304085

BibTeX
@article{DantasdeOliveira2024,
  author = {Dantas de Oliveira, Allisson and Rubio Maturana, Carles and Zarzuela Serrat, Francesc and Carvalho, Bruno Motta and Sulleiro, Elena and Prats, Clara and Veiga, Anna and Bosch, Mercedes and Zulueta, Javier and Abelló, Alberto and Sayrol, Elisa and Joseph-Munné, Joan and López-Codina, Daniel},
  title = {Development of a low-cost robotized 3D-prototype for automated optical microscopy diagnosis: An open-source system},
  journal = {PLOS ONE},
  year = {2024},
  doi = {10.1371/journal.pone.0304085}
}
Kostenlos starten →