EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Surface integrity optimization for ball-end hard milling of AISI D2 steel based on response surface methodology

Weimin Huang, Cong Wan, Guijie Wang iD, Guosong Zhang

PLOS ONE · 25.08.2023 · 18 (8) · e0290760

DOI: 10.1371/journal.pone.0290760 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS ONE, online erschienen am 25.08.2023. Verfasst von Weimin Huang und 3 weiteren Autor:innen. Beteiligte Einrichtung: College of Mechanical and Electronic Engineering, Shandong University of Science and Technology, Qingdao, China. Hauptthemen laut MEDLINE: Accidental Injuries, Data Compression. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Natural Science Foundation of Shandong Province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study focuses on systematically revealing how cutting parameters influence the surface integrity of ball-end hard milled surface of AISI D2 steel and proposing optimization scheme from surface integrity, wear resistance and fatigue resistance perspective based on response surface methodology respectively. Results can be summarized into three aspects. Firstly, radial depth of cut with percent contribution ratio (PCR) 62.05% has a decisive influence on surface roughness, followed by spindle speed 13.25% and feed per tooth 6.63%. The work hardening degree was raised from 12.5% to 38.4% when spindle speed changed from 8000 rpm to 2000 rpm. Spindle speed and radial depth of cut are the most significant factor influencing residual stress. The PCR of spindle speed and radial depth of cut reached 73.47% and 18.63% for residual stress in feed direction, 47.11% and 37.51% in step-over direction, respectively. High residual compressive stress can be generated by lowering spindle speed and radial depth of cut benefiting from the aggravated squeeze between ball-end milling cutter and workpiece. Secondly, too small feed per tooth or too small radial depth of cut should be avoided from wear resistance point because though the surface microhardness can be improved, the surface quality will also be deteriorated. The combination of high spindle speed, small feed per tooth together with small radial depth of cut can meet the wear resistance and the machining efficiency requirement. Finally, a medium-sized cutting parameter combination should be adopted to realize satisfying material removal rate and fatigue resistance. This study can be used to guide the selection of cutting parameters during ball-end milling of hardened AISI D2 steel for dies/molds manufacturing industries.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Accidental InjuriesData CompressionHumansCommerceCuspidSteel

Substanzen

Steel

Autor:innen und Institutionen

  • College of Mechanical and Electronic Engineering, Shandong University of Science and Technology, Qingdao, China.

ORCID-Profile: Guijie Wang

Förderung

  • National Natural Science Foundation of China
  • Natural Science Foundation of Shandong Province

Zitieren

APA

Huang, W., Wan, C., Wang, G., & Zhang, G. (2023). Surface integrity optimization for ball-end hard milling of AISI D2 steel based on response surface methodology. PLOS ONE, 18(8), e0290760. https://doi.org/10.1371/journal.pone.0290760

Vancouver

Huang W, Wan C, Wang G, Zhang G. Surface integrity optimization for ball-end hard milling of AISI D2 steel based on response surface methodology. PLOS ONE. 2023;18(8):e0290760. doi:10.1371/journal.pone.0290760

BibTeX
@article{Huang2023,
  author = {Huang, Weimin and Wan, Cong and Wang, Guijie and Zhang, Guosong},
  title = {Surface integrity optimization for ball-end hard milling of AISI D2 steel based on response surface methodology},
  journal = {PLOS ONE},
  year = {2023},
  volume = {18},
  number = {8},
  pages = {e0290760},
  doi = {10.1371/journal.pone.0290760}
}
Kostenlos starten →