EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of cutting velocity on surface roughness during the ultra-precision cutting of titanium alloys based on a comparison between simulation and experiment

Yonggou Lou, Lei Chen, Hongbing Wu iD, Sandy To

PLOS ONE · 2023

DOI: 10.1371/journal.pone.0288502 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS ONE, 2023. Verfasst von Yonggou Lou und 3 weiteren Autor:innen. Beteiligte Einrichtung: School of Haitian, Ningbo Polytechnic, Ningbo, China. Hauptthemen laut MEDLINE: Titanium, Alloys. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Natural Science Foundation of Ningbo, China, the Ningbo significant science and technology project.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The Ti-6Al-4V titanium alloy is a kind of light alloy material with high specific strength, corrosion resistance and heat resistance. Because of its excellent performance, it has become an important material in aerospace industry. However, this kind of alloy has very poor machinability, and rapid tool wear is a very serious problem in titanium alloy processing. At present, it is difficult to guarantee the ultra-precision machining quality of titanium alloy materials, which limits its application in high-tech fields. In order to solve this problem, the influence of cutting speed on ultra-precision cutting process of titanium alloy was analyzed comprehensively. and it was found that better surface quality could be obtained at lower cutting speed. In order to study the influence of cutting speed in ultra-precision cutting of titanium alloys, cutting experiments have been carried out. Additionally, a finite element model was established to analyze the ultra-precision cutting process. Also, the constitutive model, damage model, friction model, and heat transfer in the modeling process were discussed. The chip morphology, cutting temperature, cutting force, and surface morphology under different cutting velocities are analyzed by simulation. Then, the simulation results were compared with the experimental results. The findings show that cutting speed has great influence on the ultra-precision turning of the Ti-6Al-4V alloy and the surface roughness obtained by ultra-precision cutting of titanium alloy can be lower than 20 nm at a lower cutting speed.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

TitaniumAlloysSurface PropertiesFriction

Substanzen

titanium alloy (TiAl6V4)TitaniumAlloys

Autor:innen und Institutionen

  • School of Haitian, Ningbo Polytechnic, Ningbo, China.
  • Ningbo JoysonQuin Automotive Systems Holding Co., Ltd, Ningbo, China.
  • College of Mechanical and Energy Engineering, NingboTech University, Ningbo, China.
  • State Key Laboratory in Ultra-Precision Machining Technology, Department of Industrial and Systems Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong.

ORCID-Profile: Hongbing Wu

Förderung

  • the Natural Science Foundation of Ningbo, China
  • the Ningbo significant science and technology project

Zitieren

APA

Lou, Y., Chen, L., Wu, H., & To, S. (2023). Influence of cutting velocity on surface roughness during the ultra-precision cutting of titanium alloys based on a comparison between simulation and experiment. PLOS ONE. https://doi.org/10.1371/journal.pone.0288502

Vancouver

Lou Y, Chen L, Wu H, To S. Influence of cutting velocity on surface roughness during the ultra-precision cutting of titanium alloys based on a comparison between simulation and experiment. PLOS ONE. 2023. doi:10.1371/journal.pone.0288502

BibTeX
@article{Lou2023,
  author = {Lou, Yonggou and Chen, Lei and Wu, Hongbing and To, Sandy},
  title = {Influence of cutting velocity on surface roughness during the ultra-precision cutting of titanium alloys based on a comparison between simulation and experiment},
  journal = {PLOS ONE},
  year = {2023},
  doi = {10.1371/journal.pone.0288502}
}
Kostenlos starten →