EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Field evaluation of newly developed 3D-printed ultraviolet and green light-emitting diode traps for the collection of Culicoides species in Thailand

Yuki Fujisawa, Kandit Kornmatitsuk, Sudsaijai Kornmatitsuk, Bunlue Kornmatitsuk iD

PLOS ONE · 2023

DOI: 10.1371/journal.pone.0280673 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS ONE, 2023. Verfasst von Yuki Fujisawa und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Clinical Sciences and Public Health, Faculty of Veterinary Science, Mahidol University, Salaya, Phutthamonthon, Nakhon Pathom, Thailand. Hauptthemen laut MEDLINE: Ceratopogonidae. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Mahidol University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Culcioides biting midges (Diptera: Ceratopogonidae) are vectors of various veterinary pathogens. Suction light traps are one of the most widely used tools for vector surveillance. The present aim was to compare the efficiency for the collection of Culicoides species between newly developed 3D-printed ultraviolet (Mahidol University (MU) UV LED) and green light-emitting diode (Mahidol University (MU) Green LED) traps baited with CO 2 and UV LED Center for Disease Control (CDC) light trap (BioQuip 2770) baited with CO 2 . The experiment consisted of two replicates of a 3 × 3 Latin square design in each three sampling locations (Location 1, 2, 3 and 4, 5, 6), for 12 nights between 26th July and 7th August 2020 in Thailand. Results showed that efficiency of the MU UV LED light trap was equivalent to that of the BioQuip 2770 trap for the collection of Culicoides . Meanwhile, the efficiency of the MU Green LED light trap was lower than that of both UV LED light traps. In the analysis of Culicoides species composition and sex–age grading, a similar pattern was observed among three light traps except for Culicoides actoni Smith. The newly developed 3D-printed UV LED light trap demonstrated the following advantages over the commercial light trap: cost saving to obtain multiple units, ease of customization and standardization, and increased availability by end-users. Although further assessments in different environmental conditions are needed, this 3D-printed light trap design could minimize the constrains in vector surveillance programs worldwide.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

CeratopogonidaeHumansAnimalsThailandCarbon DioxideSpecimen HandlingPrinting, Three-Dimensional

Substanzen

Carbon Dioxide

Autor:innen und Institutionen

  • Department of Clinical Sciences and Public Health, Faculty of Veterinary Science, Mahidol University, Salaya, Phutthamonthon, Nakhon Pathom, Thailand.
  • Chulalongkorn University Demonstration Secondary School, Faculty of Education, Chulalongkorn University, Pathum Wan, Bangkok, Thailand.

ORCID-Profile: Bunlue Kornmatitsuk

Förderung

  • Mahidol University

Zitieren

APA

Fujisawa, Y., Kornmatitsuk, K., Kornmatitsuk, S., & Kornmatitsuk, B. (2023). Field evaluation of newly developed 3D-printed ultraviolet and green light-emitting diode traps for the collection of Culicoides species in Thailand. PLOS ONE. https://doi.org/10.1371/journal.pone.0280673

Vancouver

Fujisawa Y, Kornmatitsuk K, Kornmatitsuk S, Kornmatitsuk B. Field evaluation of newly developed 3D-printed ultraviolet and green light-emitting diode traps for the collection of Culicoides species in Thailand. PLOS ONE. 2023. doi:10.1371/journal.pone.0280673

BibTeX
@article{Fujisawa2023,
  author = {Fujisawa, Yuki and Kornmatitsuk, Kandit and Kornmatitsuk, Sudsaijai and Kornmatitsuk, Bunlue},
  title = {Field evaluation of newly developed 3D-printed ultraviolet and green light-emitting diode traps for the collection of Culicoides species in Thailand},
  journal = {PLOS ONE},
  year = {2023},
  doi = {10.1371/journal.pone.0280673}
}
Kostenlos starten →