EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of moulding sands on microstructural features, mechanical properties, and wear behavior of AA2024 by CO2 process

Kadapa Vijaya Bhaskar Reddy, Aruri Devaraju, Moyya Sundeep, P. Prakash, Mohammed Zubairuddin, Singuru Madhavarao, Shahid Tamboli

Advances in Science and Technology Research Journal · 01.07.2026 · 20 (7) · 241-262

DOI: 10.12913/22998624/219349 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advances in Science and Technology Research Journal, online erschienen am 01.07.2026. Verfasst von Kadapa Vijaya Bhaskar Reddy und 6 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The present study explored the feasibility of replacing conventional silica sand with industrial waste–based moulding materials—blast furnace slag and ferrochrome slag – in the CO₂ casting of AA2024 aluminium alloy. Alternative mould media have been shown in earlier research to improve cooling behaviour and lessen environmental impact; however, AA2024 alloy and its tribo-mechanical response have received little attention. The impact of these moulding sands on wear behaviour, surface finish, mechanical characteristics, and microstructural features was methodically assessed in this study. According to thermal analysis, ferrochrome slag produced refined grain structures (~75 µm) by promoting faster heat dissipation. As a result, silica sand castings exhibited the highest tensile strength due to their relatively balanced solidification and lower internal stress levels. In contrast, ferrochrome slag castings demonstrated superior microhardness and enhanced wear resistance. Due to the strong strain-hard-ening effect, blast furnace slag showed increased compressive strength. Slag-based moulds deliver competitive performance with enhanced durability under sliding conditions, as demonstrated by surface roughness and tribo-logical evaluations. Overall, the results demonstrate that blast furnace and ferrochrome slags are technically feasible and sustainable substitutes for silica sand in the production of structurally sound AA2024 cast components.

Zitieren

APA

Reddy, K. V. B., Devaraju, A., Sundeep, M., Prakash, P., Zubairuddin, M., Madhavarao, S., & Tamboli, S. (2026). Influence of moulding sands on microstructural features, mechanical properties, and wear behavior of AA2024 by CO2 process. Advances in Science and Technology Research Journal, 20(7), 241-262. https://doi.org/10.12913/22998624/219349

Vancouver

Reddy KVB, Devaraju A, Sundeep M, Prakash P, Zubairuddin M, Madhavarao S, et al. Influence of moulding sands on microstructural features, mechanical properties, and wear behavior of AA2024 by CO2 process. Advances in Science and Technology Research Journal. 2026;20(7):241-262. doi:10.12913/22998624/219349

BibTeX
@article{Reddy2026,
  author = {Reddy, Kadapa Vijaya Bhaskar and Devaraju, Aruri and Sundeep, Moyya and Prakash, P. and Zubairuddin, Mohammed and Madhavarao, Singuru and Tamboli, Shahid},
  title = {Influence of moulding sands on microstructural features, mechanical properties, and wear behavior of AA2024 by CO2 process},
  journal = {Advances in Science and Technology Research Journal},
  year = {2026},
  volume = {20},
  number = {7},
  pages = {241--262},
  doi = {10.12913/22998624/219349}
}
Kostenlos starten →