Use of pumice stone and silica fume as precursor material for the design of a geopolymer
F1000Research · 2024
DOI: 10.12688/f1000research.147701.2 ↗Kurz gefasst
Fachartikel in der Zeitschrift F1000Research, 2024. Verfasst von Alexis Iván Andrade Valle und 7 weiteren Autor:innen. Beteiligte Einrichtung: Engineering, Universitat Politecnica de Valencia, Valencia, Valencian Community, 46022, Spain. Hauptthemen laut MEDLINE: Silicates, Silicon Dioxide. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Background
Geopolymers are alternative materials to cement because they require less energy in their production process; hence, they contribute to the reduction in CO2 emissions. This study aims to evaluate the possibility of using industrial residues such as silica fume (SF) to improve the physical and mechanical properties of a pumice stone (PS)-based geopolymer.
Methods
Through an experimental methodology, the process starts with the extraction, grinding, and sieving of the raw material to carry out the physical and chemical characterization of the resulting material, followed by the dosage of the geopolymer mixture considering the factors that influence the resistance mechanical strength. Finally, the physical and mechanical properties of the geopolymer were characterized. This research was carried out in four stages: characterization of the pumice stone, design of the geopolymer through laboratory tests, application according to the dosage of the concrete, and analysis of the data through a multi-criteria analysis.
Results
It was determined that the optimal percentage of SF replacement is 10%, which to improves the properties of the geopolymer allowing to reach a maximum resistance to compression and flexion of 14.10 MPa and 4.78 MPa respectively, showing that there is a direct relationship between the percentage of SF and the resistance.
Conclusions
Geopolymer preparation involves the use of PS powder with a composition rich in silicon and aluminum. The factors influencing strength include the ratio of sodium silicate to sodium hydroxide, water content, temperature, curing time, molarity of sodium hydroxide, and binder ratio. The results showed an increase in the compression and flexural strength with 10% SF replacement. The geopolymer’s maximum compressive strength indicates its non-structural use, but it can be improved by reducing the PS powder size.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Engineering, Universitat Politecnica de Valencia, Valencia, Valencian Community, 46022, Spain.
- Engineering, Universidad Nacional de Chimborazo, Riobamba, Chimborazo Province, 060150, Ecuador.
ORCID-Profile: María Gabriela Zúñiga Rodríguez, Andrea Natalí Zárate Villacrés, Marcelo David Guerra Valladares
Zitieren
APA
Andrade Valle, A. I., Castillo Campoverde, T. O., Marcillo Zapata, C. A., Zúñiga Rodríguez, M. G., Zárate Villacrés, A. N., Guerra Valladares, M. D., Mieles Mariño, M. L., & Castillo Cevallos, J. J. (2024). Use of pumice stone and silica fume as precursor material for the design of a geopolymer. F1000Research. https://doi.org/10.12688/f1000research.147701.2
Vancouver
Andrade Valle AI, Castillo Campoverde TO, Marcillo Zapata CA, Zúñiga Rodríguez MG, Zárate Villacrés AN, Guerra Valladares MD, et al. Use of pumice stone and silica fume as precursor material for the design of a geopolymer. F1000Research. 2024. doi:10.12688/f1000research.147701.2
BibTeX
@article{AndradeValle2024,
author = {Andrade Valle, Alexis Iván and Castillo Campoverde, Tito Oswaldo and Marcillo Zapata, Cristian Andrés and Zúñiga Rodríguez, María Gabriela and Zárate Villacrés, Andrea Natalí and Guerra Valladares, Marcelo David and Mieles Mariño, Mayte Lisbeth and Castillo Cevallos, Jefferson Javier},
title = {Use of pumice stone and silica fume as precursor material for the design of a geopolymer},
journal = {F1000Research},
year = {2024},
doi = {10.12688/f1000research.147701.2}
}
EUVIMED