EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Construction of a 3D printed, human gingival MSC seeded alveolar bone implant

Hilal Selamet iD, Seyma Isik iD, Deniz Yucel iD, Vasif Hasirci iD

Journal of Applied Biomaterials & Functional Materials · 2026-07 · 24

DOI: 10.1177/22808000261452915 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Applied Biomaterials & Functional Materials, online erschienen am 01.07.2026. Verfasst von Hilal Selamet und 3 weiteren Autor:innen. Beteiligte Einrichtung: Biomaterials Center, Acibadem University, Atasehir, Istanbul, Türkiye. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Mesenchymal Stem Cells, Tissue Scaffolds, Gingiva. Die Arbeit nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: Acıbadem Mehmet Ali Aydınlar Üniversitesi.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background/objective(s)/introduction: Tissue engineered scaffolds fabricated by 3D printing promises to enhance the success rate in alveolar bone augmentation. The aim of this study was to construct and characterize a 3D printed poly(ε-caprolactone; PCL) scaffolds treated with bone morphogenetic protein 2 (BMP-2) and carrying human gingival mesenchymal stem cells (hGMSCs) for potential use in the augmentation of alveolar bone. Materials and methods: PCL scaffolds with defined pore geometry were fabricated by 3D printing using fused deposition modeling (FDM) and treated with O 2 plasma to enhance BMP-2 and cell adhesion. The scaffolds were characterized by compression testing, scanning electron microscopy (SEM), and water contact angle measurement. BMP-2 was bound to the surface, and hGMSCs from gingival connective tissue were seeded onto the scaffolds. BMP-2 was quantified by elisa. The cells were identified as stem cells based on their differentiation capacity and immunophenotypic profile. Osteogenic differentiation on BMP-2 bound scaffolds was assessed using alkaline phosphatase (ALP) activity and calcium deposition assays. Results: Compressive modulus of the PCL scaffolds (73.2 ± 17.1 MPa) was close to human alveolar bone (96.2 ± 40.6 MPa). SEM revealed a porous design with continuous struts, creating an average pore size of 400 µm and zig-zag channels suitable for cell infiltration and adhesion. O 2 plasma treatment decreased the water contact angle from 110° ± 4° to 59° ± 2°, indicating improved surface hydrophilicity. ELISA showed that over 98% of BMP-2 remained bound to the scaffold for 28 days, indicating prolonged growth factor presence during cell culture. Within the environment created, BMP-2 bound scaffolds led to a threefold increase in ALP activity and higher calcium deposition compared to controls, confirming enhanced osteogenic differentiation. Conclusion(s): 3D printed PCL scaffolds functionalized with BMP-2 and seeded with hGMSCs exhibited highly improved in vitro osteogenic properties which promises to improve alveolar bone augmentation results.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalMesenchymal Stem CellsTissue ScaffoldsGingivaHumansBone Morphogenetic Protein 2Tissue EngineeringPolyestersOsteogenesisCell DifferentiationCells, Cultured

Stichwörter der Autor:innen

3D printingalveolar bone augmentationbone morphogenetic protein 2dental tissue engineeringmesenchymal stem cells

Substanzen

Bone Morphogenetic Protein 2polycaprolactonePolyestersBMP2 protein, human

Autor:innen und Institutionen

  • Biomaterials Center, Acibadem University, Atasehir, Istanbul, Türkiye.
  • Department of Biomedical Engineering, Graduate School of Health Sciences, Acibadem University, Atasehir, Istanbul, Türkiye.
  • Department of Medical Biotechnology, Graduate School of Health Sciences, Acibadem University, Atasehir, Istanbul, Türkiye.
  • Department of Histology and Embryology, School of Medicine, Acibadem Univesity, Atasehir,Istanbul, Türkiye.
  • Department of Biomaterials, Acibadem University, Atasehir, Istanbul, Istanbul, Türkiye.
  • BIOMATEN, Center of Excellence in Biomaterials and Tissue Engineering, Middle East Technical University, Cankaya, Ankara, Türkiye.

ORCID-Profile: Hilal Selamet, Seyma Isik, Deniz Yucel, Vasif Hasirci

Förderung

  • Acıbadem Mehmet Ali Aydınlar Üniversitesi

Zitieren

APA

Selamet, H., Isik, S., Yucel, D., & Hasirci, V. (2026). Construction of a 3D printed, human gingival MSC seeded alveolar bone implant. Journal of Applied Biomaterials & Functional Materials, 24. https://doi.org/10.1177/22808000261452915

Vancouver

Selamet H, Isik S, Yucel D, Hasirci V. Construction of a 3D printed, human gingival MSC seeded alveolar bone implant. Journal of Applied Biomaterials & Functional Materials. 2026;24. doi:10.1177/22808000261452915

BibTeX
@article{Selamet2026,
  author = {Selamet, Hilal and Isik, Seyma and Yucel, Deniz and Hasirci, Vasif},
  title = {Construction of a 3D printed, human gingival MSC seeded alveolar bone implant},
  journal = {Journal of Applied Biomaterials & Functional Materials},
  year = {2026},
  volume = {24},
  doi = {10.1177/22808000261452915}
}
Kostenlos starten →