EUVIMEDEUVIMED entdecken
Crossref

Experimental, FEA, and machine learning studies on wear behavior of LM13 aluminum hybrid composites reinforced with zircon and graphite

Ravitej Yellampalli Prakash, Bommishetty Venkata Naga Ramakumar, Keshavamurthy R, Sandeep S Patil, Vishnu Vijay Kumar, Adarsha Hiriyannaiah

Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology · 17.08.2025

DOI: 10.1177/13506501251367549 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, online erschienen am 17.08.2025. Verfasst von Ravitej Yellampalli Prakash und 5 weiteren Autor:innen. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 42 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper examines applied load and zircon reinforcement influence on LM13 alloy composites’ wear behavior. LM13 was reinforced with 3 wt.% graphite with 3, 6, 9, and 12 weight percent of zircon utilizing a stir casting technique with a chill end to achieve unidirectional solidification. Wear tests were conducted on specimen's chill end using a pin-on-disc apparatus under loads of 30 N, to 70 N in steps of 10 N incremental. The results indicated that when the amount of zircon went up, the wear rate dropped, reaching a minimum at 9 wt.% zircon, then slightly increasing at 12 wt.%. Specifically, wear rate reduced from 4.2 × 10 −3 mm³/Nm at 3 wt.% zircon to 2.7 × 10 −3 mm³/Nm at 9 wt.% zircon, before rising to 3.5 × 10 −3 mm³/Nm at 12 wt.%, establishing 9 wt.% zircon as the optimum reinforcement. Finite Element Analysis (FEA) had been used to simulate wear behavior, and its predictions aligned well with experimental data, with deviations under 5%. Both experimental and FEA results confirmed that wear rate increases proportionally with applied load. Additionally, machine learning techniques were employed to validate the observed trends, enhancing the reliability of the findings. Microstructural analysis through Field Emission Scanning Electron Microscopy showed evidence of plastic deformation and delamination at higher stress levels, compromising material integrity. Notably, the composite with 9 wt.% zircon exhibited reduced wear deformation and minimal microstructural damage, confirming its effectiveness in improving wear resistance.

Zitieren

APA

Prakash, R. Y., Ramakumar, B. V. N., R, K., Patil, S. S., Kumar, V. V., & Hiriyannaiah, A. (2025). Experimental, FEA, and machine learning studies on wear behavior of LM13 aluminum hybrid composites reinforced with zircon and graphite. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology. https://doi.org/10.1177/13506501251367549

Vancouver

Prakash RY, Ramakumar BVN, R K, Patil SS, Kumar VV, Hiriyannaiah A. Experimental, FEA, and machine learning studies on wear behavior of LM13 aluminum hybrid composites reinforced with zircon and graphite. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology. 2025. doi:10.1177/13506501251367549

BibTeX
@article{Prakash2025,
  author = {Prakash, Ravitej Yellampalli and Ramakumar, Bommishetty Venkata Naga and R, Keshavamurthy and Patil, Sandeep S and Kumar, Vishnu Vijay and Hiriyannaiah, Adarsha},
  title = {Experimental, FEA, and machine learning studies on wear behavior of LM13 aluminum hybrid composites reinforced with zircon and graphite},
  journal = {Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology},
  year = {2025},
  doi = {10.1177/13506501251367549}
}
Kostenlos starten →