EUVIMEDEUVIMED entdecken
Scoping ReviewOpen Access · CC BY 4.0

Computer-Aided Design and Computer-Aided Manufacturing Technology for Conducting Nasoalveolar Molding for Infants With Cleft Lip and Palate: A Scoping Review

Bach Kim Nguyen iD, Camila Caro iD, Kyle Stevens iD, Gabriella A Garisto iD, Yoav Finer iD

The Cleft Palate Craniofacial Journal · 2026-08 · 63 (8) · 2698-2712

DOI: 10.1177/10556656251363400 ↗

Kurz gefasst

Scoping Review in der Zeitschrift The Cleft Palate Craniofacial Journal, online erschienen am 11.09.2025. Verfasst von Bach Kim Nguyen und 4 weiteren Autor:innen. Beteiligte Einrichtung: Graduate Orthodontics, Faculty of Dentistry, University of Toronto, Toronto, Ontario, Canada. Hauptthemen laut MEDLINE: Cleft Lip, Computer-Aided Design, Cleft Palate, Nasoalveolar Molding. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

To identify, describe, and characterize computer-aided design and computer-aided manufacturing (CAD/CAM) methods for nasoalveolar molding (NAM) based on a structured search of scientific literature.

Design

Scoping review was conducted following the PRISMA-ScR guidelines. Searches were done in MEDLINE, Embase, Web of Science, Cochrane Library, and Scopus. Screening and data extraction were performed. Patients Infants with unrepaired, nonsyndromic, complete unilateral cleft lip and palate (UCLP), or bilateral cleft lip and palate (BCLP).

Intervention

CAD/CAM NAM. Main Outcome Measures Outcome measures were the digitization, virtual modeling, and manufacturing protocols.

Results

Thirteen articles were included. CAD/CAM NAM involved digitizing the maxilla, designing step-by-step (stepwise) alveolar movements or expansion of plates, then manufacturing plates manually or through 3D printing. Four methods were characterized based on the virtual modeling and manufacturing techniques employed: stepwise alveolar molding and manually fabricated plates (SM_MP); stepwise alveolar molding and 3D-printed plates (SM_3P); stepwise plate expansion and 3D-printed plates (SPE_3P); and semi-automated plate expansion and 3D-printed plates (SAPE_3P). The SM_MP method was the most common, followed by the SM_3P, SPE_3P, and SAPE_3P methods. All methods were applied to treat infants with UCLP, whereas only the SM_MP and SM_3P methods were used for infants with BCLP.

Conclusions

This scoping review provides an overview of 4 CAD/CAM methods for NAM. The SM_MP and SM_3P methods simulate alveolar molding; however, the SM_3P method exhibits more advanced design and manufacturing of plates. The SPE_3P and SAPE_3P methods design consecutively enlarged plates, with the latter employing a semi-automated protocol.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Cleft LipComputer-Aided DesignCleft PalateNasoalveolar MoldingHumansInfantPrinting, Three-Dimensional

Stichwörter der Autor:innen

3D printingdigitalpresurgical infant orthopedics

Autor:innen und Institutionen

  • Graduate Orthodontics, Faculty of Dentistry, University of Toronto, Toronto, Ontario, Canada.
  • Division of Orthodontics, Department of Dentistry, The Hospital for Sick Children, University of Toronto, Toronto, Ontario, Canada.
  • Division of Pediatric Dentistry, Department of Dentistry, The Hospital for Sick Children, University of Toronto, Toronto, Ontario, Canada.
  • Faculty of Dentistry and Institute of Biomedical Engineering, University of Toronto, Toronto, Ontario, Canada.

ORCID-Profile: Bach Kim Nguyen, Camila Caro, Kyle Stevens, Gabriella A Garisto, Yoav Finer

Zitieren

APA

Nguyen, B. K., Caro, C., Stevens, K., Garisto, G. A., & Finer, Y. (2026). Computer-Aided Design and Computer-Aided Manufacturing Technology for Conducting Nasoalveolar Molding for Infants With Cleft Lip and Palate: A Scoping Review. The Cleft Palate Craniofacial Journal, 63(8), 2698-2712. https://doi.org/10.1177/10556656251363400

Vancouver

Nguyen BK, Caro C, Stevens K, Garisto GA, Finer Y. Computer-Aided Design and Computer-Aided Manufacturing Technology for Conducting Nasoalveolar Molding for Infants With Cleft Lip and Palate: A Scoping Review. The Cleft Palate Craniofacial Journal. 2026;63(8):2698-2712. doi:10.1177/10556656251363400

BibTeX
@article{Nguyen2026,
  author = {Nguyen, Bach Kim and Caro, Camila and Stevens, Kyle and Garisto, Gabriella A and Finer, Yoav},
  title = {Computer-Aided Design and Computer-Aided Manufacturing Technology for Conducting Nasoalveolar Molding for Infants With Cleft Lip and Palate: A Scoping Review},
  journal = {The Cleft Palate Craniofacial Journal},
  year = {2026},
  volume = {63},
  number = {8},
  pages = {2698--2712},
  doi = {10.1177/10556656251363400}
}
Kostenlos starten →