EUVIMEDEUVIMED entdecken
Crossref

The influence of MoS 2 lubricity on the secondary cutting performance of PCD micro-groove textured tools

Yongqian Chen, Yifan Cao, Jialin Liu, Shirui Guo, Yinghao Cui, Xiaolei Li, Bo Zheng, Yue Zhao, XiaoLu Wang, Xiwang Wu, Xianshi Jia, Lujun Cui

Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering · 01.08.2026

DOI: 10.1177/09544089261471953 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, online erschienen am 01.08.2026. Verfasst von Yongqian Chen und 11 weiteren Autor:innen. Die Arbeit nennt 30 Literaturangaben. Gefördert von: Open Project of Hubei Key Laboratory of Digital Textile Equipment, State Key Laboratory of Ultrafast Optical Science and Technology, Natural Science Foundation of Hunan Province.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Micro-textured cutting tools possess unique advantages in reducing cutting forces, lowering chip temperatures, minimizing tool wear, and improving machined surface quality. Nevertheless, the secondary cutting effect induced by micro-textures impairs texture integrity and aggravates tool wear. Hence, it is of great significance to explore evaluation approaches and suppression strategies for the secondary cutting of micro-textured tools. This paper presents a method to evaluate the secondary cutting effect of micro-textured tools based on the roughness of chip scratches, which is verified via experiments. In the tests, a femtosecond laser was employed to fabricate micro-groove textures with inclination angles of 0°, 30°, 60°, and 90° on the rake face of polycrystalline diamond tools, and MoS 2 solid lubricant was filled into these micro-grooves. Dry cutting experiments were then carried out. Using scanning electron microscopy, laser confocal microscopy, and a hardness tester, the performances of conventional tools, ordinary micro-textured tools, and micro-textured tools with MoS 2 solid lubricant were evaluated through a comparative analysis of the rake face morphology, chip roughness, and chip hardness, with particular attention to the relative magnitudes of these parameters among the three tool conditions. The results indicate that micro-groove textured tools with textures parallel to the main cutting edge exhibit weaker adverse effects. During cutting, MoS 2 solid lubricant delivers good lubrication and friction reduction, further optimizing the overall performance of micro-groove textured tools. The hardness of chips generated by lubricant-filled micro-groove textured tools is 0.9% and 4.12% higher than that from plain micro-textured tools and conventional tools, respectively. Meanwhile, the roughness of chips obtained with MoS 2 lubrication is 38.10% lower than that from tools with only micro-groove textures.

Förderung

  • Open Project of Hubei Key Laboratory of Digital Textile Equipment
  • State Key Laboratory of Ultrafast Optical Science and Technology
  • Natural Science Foundation of Hunan Province
  • Mechanical Industry Key Laboratory of Optical Sensing and Testing Technology
  • Open Fund of Henan General Aviation Technology Key Laboratory
  • Key project for school achievement cultivation
  • Key Scientific Research Project of Colleges and Universities in Henan Province
  • Key Scientific Research Project of Institutions of Higher Education in Henan Province

Zitieren

APA

Chen, Y., Cao, Y., Liu, J., Guo, S., Cui, Y., Li, X., Zheng, B., Zhao, Y., Wang, X., Wu, X., Jia, X., & Cui, L. (2026). The influence of MoS 2 lubricity on the secondary cutting performance of PCD micro-groove textured tools. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering. https://doi.org/10.1177/09544089261471953

Vancouver

Chen Y, Cao Y, Liu J, Guo S, Cui Y, Li X, et al. The influence of MoS 2 lubricity on the secondary cutting performance of PCD micro-groove textured tools. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering. 2026. doi:10.1177/09544089261471953

BibTeX
@article{Chen2026,
  author = {Chen, Yongqian and Cao, Yifan and Liu, Jialin and Guo, Shirui and Cui, Yinghao and Li, Xiaolei and Zheng, Bo and Zhao, Yue and Wang, XiaoLu and Wu, Xiwang and Jia, Xianshi and Cui, Lujun},
  title = {The influence of MoS 2 lubricity on the secondary cutting performance of PCD micro-groove textured tools},
  journal = {Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering},
  year = {2026},
  doi = {10.1177/09544089261471953}
}
Kostenlos starten →