EUVIMEDEUVIMED entdecken
Crossref

Evaluation of multiple residual stress components in a thick welded joint using extended contour method

Yi Yan, Chuan Liu, Chaowen Li, Jinlong Wang, Minjie Yue, Jianxin Wang

Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering · 2026-08 · 240 (4) · 3834-3844

DOI: 10.1177/09544089241286607 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, online erschienen am 03.10.2024. Verfasst von Yi Yan und 5 weiteren Autor:innen. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 37 Literaturangaben. Gefördert von: the National Natural Science Foundation of China, Ji Hua Laboratory Program, Science and Technology Projects in Guangzhou.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The conventional contour method (CM) needs multiple cuts at different locations to obtain the multiple components of residual stress in a specimen. To improve the convectional CM, an extended CM was proposed in the present study to determine the multiple stress components in a thick butt-welded joint without cutting at different locations. First, the longitudinal residual stress in the specimen was measured with the CM, then a thin slice was cut from the after-cut specimen, and the remaining transverse stress in the slice was measured with the X-ray diffraction method and the released transverse stress of the slice was constructed by the finite element analysis (FEA), and finally, the transverse stress on the same cross-section was obtained by the superposition of the remaining and the released transverse stresses on the slice. A two-cut CM was also carried out to get the transverse stress along the weld line center. The stress distribution characteristics of the specimen and the release extent of the transverse stress in the slice were discussed. The results show that the extended CM can evaluate the original biaxial residual stresses on a cross-section without multiple cuts at different locations. The transverse stress distribution trend obtained by the extended CM is close to that from the two-cut CM. Without considering the compressive stress induced by ultrasonic impact treatment, the longitudinal stress in the weld region is tensile with a maximum value of 550 MPa and the transverse stress at the weld line center is self-equilibrating with a maximum value reaching 552 MPa. Two peaks of tensile longitudinal and transverse stress appear at a certain distance beneath the top and bottom surfaces. When cutting a thin slice with a thickness of 5 mm along the transverse direction from the after-cut specimen, over 82% of the original tensile transverse stresses are retained in the slice.

Förderung

  • the National Natural Science Foundation of China
  • Ji Hua Laboratory Program
  • Science and Technology Projects in Guangzhou
  • Scientific Research Project of the Education Department of Guangdong Province
  • Basic and Applied Basic Research Foundation of Guangdong Province

Zitieren

APA

Yan, Y., Liu, C., Li, C., Wang, J., Yue, M., & Wang, J. (2026). Evaluation of multiple residual stress components in a thick welded joint using extended contour method. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 240(4), 3834-3844. https://doi.org/10.1177/09544089241286607

Vancouver

Yan Y, Liu C, Li C, Wang J, Yue M, Wang J. Evaluation of multiple residual stress components in a thick welded joint using extended contour method. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering. 2026;240(4):3834-3844. doi:10.1177/09544089241286607

BibTeX
@article{Yan2026,
  author = {Yan, Yi and Liu, Chuan and Li, Chaowen and Wang, Jinlong and Yue, Minjie and Wang, Jianxin},
  title = {Evaluation of multiple residual stress components in a thick welded joint using extended contour method},
  journal = {Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering},
  year = {2026},
  volume = {240},
  number = {4},
  pages = {3834--3844},
  doi = {10.1177/09544089241286607}
}
Kostenlos starten →