EUVIMEDEUVIMED entdecken
Crossref

The evaluation of the aging process in 15-5 PH materials in terms of formability and microstructure

Ali Haydar Özcan, İbrahim Karaağaç, Mehmet Yasin Demirel, Ali Evren Işik

Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering · 2026-06 · 240 (3) · 2878-2886

DOI: 10.1177/09544089241282072 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, online erschienen am 07.10.2024. Verfasst von Ali Haydar Özcan und 3 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 40 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this study, the effects of aging heat treatment of 15-5 PH stainless steel material on the mechanical properties, microstructure, and formability were investigated. Instead of cooling in air, cooling in the oven spontaneously was applied in the oven for the first time. Experimental studies show that aging heat treatment was applied for H900, H1025, and H1150 conditions at temperatures of 482 °C, 552 °C, and 621 °C, respectively, and 60 min for H900 and 240 min for H1025 and H1150. It has been observed that controlled cooling in the oven increases the mechanical values of the material obtained by cooling in the air by 8%–10%. The microstructures of the conditions after heat treatment were also examined, and it was observed that the cooling aging heat treatment in the oven caused precipitation hardening in the microstructure of the material. In addition, when evaluating the formability of the results using V-bending, it was observed that materials which could not withstand bending beyond 75° in Condition A (Con A), the initial state of the material, were smoothly shaped in all conditions and at all angles as a result of the cooling process in the oven. A decrease in spring-back angles has been detected due to the decrease in mechanical properties caused by increasing aging temperature. The highest spring-back value was also observed on a 75° bending die with 10.948° in the H900 condition which has the highest mechanical properties.

Zitieren

APA

Özcan, A. H., Karaağaç, İ., Demirel, M. Y., & Işik, A. E. (2026). The evaluation of the aging process in 15-5 PH materials in terms of formability and microstructure. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 240(3), 2878-2886. https://doi.org/10.1177/09544089241282072

Vancouver

Özcan AH, Karaağaç İ, Demirel MY, Işik AE. The evaluation of the aging process in 15-5 PH materials in terms of formability and microstructure. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering. 2026;240(3):2878-2886. doi:10.1177/09544089241282072

BibTeX
@article{zcan2026,
  author = {Özcan, Ali Haydar and Karaağaç, İbrahim and Demirel, Mehmet Yasin and Işik, Ali Evren},
  title = {The evaluation of the aging process in 15-5 PH materials in terms of formability and microstructure},
  journal = {Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering},
  year = {2026},
  volume = {240},
  number = {3},
  pages = {2878--2886},
  doi = {10.1177/09544089241282072}
}
Kostenlos starten →