EUVIMEDEUVIMED entdecken
Crossref

Experimental study on grinding process of Al-Mg 2 Si aluminum matrix composites

Hailong Sun, Qi Gao, Quanzhao Wang, Bintong Zhao, Dake Yun

Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering · 2026-06 · 240 (3) · 2611-2621

DOI: 10.1177/09544089241272755 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, online erschienen am 02.09.2024. Verfasst von Hailong Sun und 4 weiteren Autor:innen. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 33 Literaturangaben. Gefördert von: National Natural Science Foundation of China, Natural Science Foundation of Liaoning Province.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

As an aluminum-based reinforcement, Mg 2 Si particles have excellent properties such as high hardness, high melting point, and high elastic modulus compared with other reinforcements and are widely used in aerospace and automobile fields. However, there is little research on the cutting mechanism of this material. In order to explore the surface grinding mechanism of Mg 2 Si/Al composites, Grinding simulation of low-volume fraction Mg 2 Si/Al composites was carried out by ABAQUS, and the influence of different positions of matrix and particle removal on the surface quality of Mg 2 Si/Al composites was expounded. The plane reverse grinding test was carried out by using CBN (boron nitride) grinding wheel. The L 16 (4 3 ) orthogonal test and three groups of single factor tests were designed. The orthogonal results show that the linear velocity of the grinding wheel has the greatest influence on the surface roughness, and the feed rate and grinding depth are significantly smaller. The range analysis shows that the optimal grinding parameters are: v s = 35 m/s, v w = 0.75 m/min, a p = 0.015 mm. The regression equation for surface roughness was established by using MATLAB. The single factor results show that the surface quality is obviously improved by increasing the linear velocity of the grinding wheel and reducing the feed rate and grinding depth through the observation of the morphology of the processed specimen. The analysis results show that defects such as pits, protrusions, burrs, and a small amount of fish-scale-like on the machined surface are mainly caused by the linear velocity of the grinding wheel, the pulling force of the grinding wheel, and the adhesion of the debris. The defects such as particle micro-cracks, particle pull-out, and matrix cracking on the subsurface, are mainly caused by the compressive stress of the grinding wheel and the stress concentration of the particles. The research results have guiding significance for future composite material cutting research and actual cutting processing.

Förderung

  • National Natural Science Foundation of China
  • Natural Science Foundation of Liaoning Province

Zitieren

APA

Sun, H., Gao, Q., Wang, Q., Zhao, B., & Yun, D. (2026). Experimental study on grinding process of Al-Mg 2 Si aluminum matrix composites. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 240(3), 2611-2621. https://doi.org/10.1177/09544089241272755

Vancouver

Sun H, Gao Q, Wang Q, Zhao B, Yun D. Experimental study on grinding process of Al-Mg 2 Si aluminum matrix composites. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering. 2026;240(3):2611-2621. doi:10.1177/09544089241272755

BibTeX
@article{Sun2026,
  author = {Sun, Hailong and Gao, Qi and Wang, Quanzhao and Zhao, Bintong and Yun, Dake},
  title = {Experimental study on grinding process of Al-Mg 2 Si aluminum matrix composites},
  journal = {Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering},
  year = {2026},
  volume = {240},
  number = {3},
  pages = {2611--2621},
  doi = {10.1177/09544089241272755}
}
Kostenlos starten →