EUVIMEDEUVIMED entdecken
Crossref

Design and control of a compact high-power-density two-DOF hydraulic gripper

Yuanchun Luo, Huaizhi Zong, Zhangwei Cao, Yong Li, Baizhou Ma, Weidi Huang, Junhui Zhang, Bing Xu

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science · 2026-12 · 240 (23) · 9856-9870

DOI: 10.1177/09544062261480787 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, online erschienen am 28.08.2026. Verfasst von Yuanchun Luo und 7 weiteren Autor:innen. Die Arbeit nennt 24 Literaturangaben. Gefördert von: National Science Foundation for Distinguished Young Scholars of China, Postdoctoral Innovative Talent Support Program.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Compactness and lightweight characteristics of end-effectors are crucial for ensuring the high mobility of legged robots in complex unstructured environments. However, existing electric and pneumatic counterparts have limited output capacity, while traditional hydraulic end-effectors often suffer from excessive weight and complex piping layouts that cause motion interference and joint space limitations. This paper presents the design, modeling, and control of a compact, high-power-density 2-DOF hydraulic gripper. First, a novel annular swing actuator is coaxially nested with a linear gripping mechanism to compress axial space. Unlike typical 1-DOF designs, this 2-DOF architecture integrates independent swing (50 Nm) and gripping (1000 N) capabilities into a 1.17 kg prototype, allowing it to perform rotational tasks like valve turning without relying on the movement of upstream joints. By incorporating a tubeless embedded fluid channel design, space occupancy and physical constraints on joint movement are minimized, enhancing structural integration. Second, a state-space model incorporating servo valve dynamics, flow continuity, and load balance is established to address inherent nonlinearities and external disturbances. A sliding mode controller (SMC) is implemented to validate the tracking performance and robustness of the proposed hardware. Simulation and experimental results demonstrate steady-state errors for swing and gripping as low as 0.56° and 0.40 mm, respectively. The results demonstrate the feasibility of the compact high-power-density design, offering a potential solution to integration challenges for lightweight mobile platforms and contributing to actuator development for high-performance legged robots.

Förderung

  • National Science Foundation for Distinguished Young Scholars of China
  • Postdoctoral Innovative Talent Support Program

Zitieren

APA

Luo, Y., Zong, H., Cao, Z., Li, Y., Ma, B., Huang, W., Zhang, J., & Xu, B. (2026). Design and control of a compact high-power-density two-DOF hydraulic gripper. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 240(23), 9856-9870. https://doi.org/10.1177/09544062261480787

Vancouver

Luo Y, Zong H, Cao Z, Li Y, Ma B, Huang W, et al. Design and control of a compact high-power-density two-DOF hydraulic gripper. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science. 2026;240(23):9856-9870. doi:10.1177/09544062261480787

BibTeX
@article{Luo2026,
  author = {Luo, Yuanchun and Zong, Huaizhi and Cao, Zhangwei and Li, Yong and Ma, Baizhou and Huang, Weidi and Zhang, Junhui and Xu, Bing},
  title = {Design and control of a compact high-power-density two-DOF hydraulic gripper},
  journal = {Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science},
  year = {2026},
  volume = {240},
  number = {23},
  pages = {9856--9870},
  doi = {10.1177/09544062261480787}
}
Kostenlos starten →