EUVIMEDEUVIMED entdecken
Crossref

In vitro characterization of 3D printed polycaprolactone/graphene oxide scaffolds impregnated with alginate and gelatin hydrogels for bone tissue engineering

Shaghayegh Amini-Mosleh-Abadi, Zahra Yazdanpanah, Farinaz Ketabat, Mahya Saadatifar, Mohammad Mohammadi, Nima Salimi, Azade Asef Nejhad, Ali Sadeghianmaryan iD

Journal of Biomaterials Applications · 2025

DOI: 10.1177/08853282251336552 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomaterials Applications, 2025. Verfasst von Shaghayegh Amini-Mosleh-Abadi und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Biomedical Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran. Hauptthemen laut MEDLINE: Graphite, Polyesters, Tissue Engineering, Tissue Scaffolds. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 66 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To achieve successful bone tissue engineering (BTE), it is necessary to fabricate a biomedical scaffold with appropriate structure as well as favorable composition. Despite a broad range of studies, this remains a challenge, highlighting the need for a better understanding of how structural features (e.g., pore size) and scaffold composition influence mechanical and physical properties, as well as cellular behavior. Therefore, the objective of this study was to characterize physical properties (swelling, degradation), mechanical properties (compressive modulus), and cellular behavior in relation to varying compositions (referred to composite and hybrid scaffolds) as well as varying pore sizes in three-dimensional (3D) printed scaffolds. Composite scaffolds were fabricated from polycaprolactone (PCL) and two different graphene oxide (GO) (3% and 9% (w/v)) concentrations. Additionally, hybrid scaffolds were fabricated by impregnating 3D printed scaffolds in a hydrogel blend of alginate/gelatin. Pore sizes of 400, 1000, and 1500 μm were investigated in this study to assess their effect on the scaffold properties. Our findings showed that swelling and degradation properties were enhanced by (I) the addition of GO as well as introduction of both hydrogel and highest concentration of GO (9% (w/v) GO) into the polymeric matrix of PCL, and (II) increasing the pore size within the scaffolds. Mechanical testing revealed that compressive elastic modulus increased with decreasing pore size, incorporation of GO, and increasing GO content into the matrix of PCL. Although our investigated scaffolds with various pore sizes did not show comparable elastic moduli to that of cortical bone, they exhibited an elastic modulus range (∼31–48 MPa) matching that of trabecular bone. The highest compressive modulus (∼48 MPa) was observed in scaffolds of PCL/9% (w/v) GO (composite scaffolds) with the pore size of 400 μm. Cell viability assay demonstrated high MG-63 cell survival (greater than 70%) in all composite and hybrid scaffolds (indicating scaffold biocompatibility) except PCL/3% (w/v) GO scaffolds. The findings of this study contribute to the field of BTE by providing scaffold design insights in terms of pore size and composition.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

GraphitePolyestersTissue EngineeringTissue ScaffoldsHydrogelsGelatinAlginatesPrinting, Three-DimensionalHumansBone and BonesPorosityCompressive StrengthMaterials TestingBiocompatible Materials

Stichwörter der Autor:innen

Three-dimensional printingalginatebone scaffoldgelatingraphen oxideimpregnationpolycaprolactone

Substanzen

GraphitepolycaprolactonePolyestersHydrogelsGelatingraphene oxideAlginatesBiocompatible Materials

Autor:innen und Institutionen

  • Department of Biomedical Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran.
  • Division of Biomedical Engineering, College of Engineering, University of Saskatchewan, Saskatoon, SK, Canada.
  • Former Postdoctoral Research Fellow, Department of Biomedical Engineering, University of Memphis, Memphis, TN, USA.

ORCID-Profile: Ali Sadeghianmaryan

Zitieren

APA

Amini-Mosleh-Abadi, S., Yazdanpanah, Z., Ketabat, F., Saadatifar, M., Mohammadi, M., Salimi, N., Asef Nejhad, A., & Sadeghianmaryan, A. (2025). In vitro characterization of 3D printed polycaprolactone/graphene oxide scaffolds impregnated with alginate and gelatin hydrogels for bone tissue engineering. Journal of Biomaterials Applications. https://doi.org/10.1177/08853282251336552

Vancouver

Amini-Mosleh-Abadi S, Yazdanpanah Z, Ketabat F, Saadatifar M, Mohammadi M, Salimi N, et al. In vitro characterization of 3D printed polycaprolactone/graphene oxide scaffolds impregnated with alginate and gelatin hydrogels for bone tissue engineering. Journal of Biomaterials Applications. 2025. doi:10.1177/08853282251336552

BibTeX
@article{AminiMoslehAbadi2025,
  author = {Amini-Mosleh-Abadi, Shaghayegh and Yazdanpanah, Zahra and Ketabat, Farinaz and Saadatifar, Mahya and Mohammadi, Mohammad and Salimi, Nima and Asef Nejhad, Azade and Sadeghianmaryan, Ali},
  title = {In vitro characterization of 3D printed polycaprolactone/graphene oxide scaffolds impregnated with alginate and gelatin hydrogels for bone tissue engineering},
  journal = {Journal of Biomaterials Applications},
  year = {2025},
  doi = {10.1177/08853282251336552}
}
Kostenlos starten →