EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Advanced ultrasonic characterization of recycled steel fiber-reinforced mortars: Integrating nonlinear parameters for optimal fiber dosage determination

Umar Amjad iD, Mohammad R Irshidat, Hamad Alnuaimi, Muni Raj Maurya, Naeem Albeitjali, Riyamol K Razack, Hashem Y Kailani, Kishor Kumar Sadasivuni, Tribikram Kundu

Science Progress · 2026-04 · 109 (2)

DOI: 10.1177/00368504261447149 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Science Progress, online erschienen am 27.04.2026. Verfasst von Umar Amjad und 8 weiteren Autor:innen. Beteiligte Einrichtung: Center for Advanced Materials, Qatar University, Doha, Qatar. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 73 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: Qatar University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigates the use of recycled steel fibers (RSF) derived from waste tires as reinforcement in cementitious mortar composites, assessing both mechanical performance and internal structural integrity. Four mortar mixtures containing 0%, 0.5%, 1.0% and 1.5% RSF by volume were prepared and tested at 28 days using compressive and flexural strength testing alongside a suite of ultrasonic diagnostic methods including ultrasonic pulse velocity (UPV), the nonlinear parameter β, the sideband peak count index (SPC-I) and the spectral dissipation index (SDI). UPV measurements remained largely unchanged across all mixtures at 3200 to 3400 m/s revealing its limited sensitivity to fiber-induced microstructural changes. In contrast the nonlinear parameter β and hybrid parameter SDI both exhibited a distinct U-shaped trend with minimum values recorded at 1.0% RSF signaling optimal fiber distribution and matrix integrity at that dosage. At 1.5% RSF both parameters increased, suggesting the onset of fiber clustering and microstructural deterioration. SPC-I showed a moderate correlation with compressive strength while its minimum at 0.5% RSF reflects defect-dominated behavior at low fiber content rather than an optimal dosage. Statistical analysis confirmed there was no significant difference in compressive strength between the 1.0% and 1.5% dosages with a p-value of 0.51. The convergence of near-maximum mechanical strength and minimum nonlinear ultrasonic response at 1.0% RSF collectively identifies this as the optimal dosage. One methodological consideration worth noting is that different material batches from the same supplier were used for each dosage level to reflect real-world commercial variability. This introduces a batch-dosage confounding effect that may limit the broader generalizability of the findings. Nevertheless, convergent evidence from multiple independent measurement techniques supports the conclusion that dosage is the primary influencing factor within the tested material range.

Schlagwörter

Stichwörter der Autor:innen

higher harmonic generationnondestructive evaluationrecycled steel fiberssideband peak count indexspectral dissipation indexsustainable construction materialsultrasonic pulse velocity

Autor:innen und Institutionen

  • Center for Advanced Materials, Qatar University, Doha, Qatar.
  • Department of Civil and Environmental Engineering, Qatar University, Doha, Qatar.
  • Department of Civil and Architectural Engineering and Mechanics, University of Arizona, Tucson, AZ, USA.

ORCID-Profile: Umar Amjad

Förderung

  • Qatar University

Zitieren

APA

Amjad, U., Irshidat, M. R., Alnuaimi, H., Maurya, M. R., Albeitjali, N., Razack, R. K., Kailani, H. Y., Sadasivuni, K. K., & Kundu, T. (2026). Advanced ultrasonic characterization of recycled steel fiber-reinforced mortars: Integrating nonlinear parameters for optimal fiber dosage determination. Science Progress, 109(2). https://doi.org/10.1177/00368504261447149

Vancouver

Amjad U, Irshidat MR, Alnuaimi H, Maurya MR, Albeitjali N, Razack RK, et al. Advanced ultrasonic characterization of recycled steel fiber-reinforced mortars: Integrating nonlinear parameters for optimal fiber dosage determination. Science Progress. 2026;109(2). doi:10.1177/00368504261447149

BibTeX
@article{Amjad2026,
  author = {Amjad, Umar and Irshidat, Mohammad R and Alnuaimi, Hamad and Maurya, Muni Raj and Albeitjali, Naeem and Razack, Riyamol K and Kailani, Hashem Y and Sadasivuni, Kishor Kumar and Kundu, Tribikram},
  title = {Advanced ultrasonic characterization of recycled steel fiber-reinforced mortars: Integrating nonlinear parameters for optimal fiber dosage determination},
  journal = {Science Progress},
  year = {2026},
  volume = {109},
  number = {2},
  doi = {10.1177/00368504261447149}
}
Kostenlos starten →