Effect of Cu addition on phase evolution, mechanical properties, corrosion behavior, and cytocompatibility of Ti–25Nb alloys fabricated by cold isostatic pressing
Powder Metallurgy · 20.11.2026
DOI: 10.1177/00325899261505087 ↗Kurz gefasst
Fachartikel in der Zeitschrift Powder Metallurgy, online erschienen am 20.11.2026. Verfasst von Cahya Sutowo und 14 weiteren Autor:innen. Die Arbeit nennt 32 Literaturangaben. Gefördert von: RIIM LPDP Grant and BRIN, Research Organization for Nanotechnology and Materials – National Research and Innovation Agency.
Abstract (Originalsprache)
Titanium metal is widely used as an implant material due to its biocompatibility; however, further improvements are still required in terms of strength and corrosion resistance. This study evaluated the effect of Cu addition (0, 3, 6, and 9 wt.%) in Ti–25Nb alloys on microstructure, mechanical properties, corrosion resistance, and cytotoxic properties on MC-3T3-E1 cell lines. The alloy was fabricated using powder metallurgy via cold isostatic pressing at 30 MPa for 8 min. Then continued with a sintering process at 1300 °C for 4 h using a vacuum tube furnace with an inert environment using argon gas. X-ray diffraction analysis showed the formation of the Ti 2 Cu phase at high Cu content. The microstructure remains lamellar across all compositions, with progressive refinement of the lamellar structure observed as the Cu content increases, particularly at 6 and 9 wt.%. The crystallite size of the β-Ti phase increased from 26.1 nm for the Ti–25Nb alloy without copper addition to 43.6 nm for the alloy with 6 wt.% Cu; then the crystallite size decreased to 29.9 nm for the alloy with the addition of 9 wt.% Cu, indicating that excessive Ti 2 Cu precipitation could inhibit the growth of β crystals. It was shown that the hardness increased from 243.9 to 320.2 HV, and the density from 4.54 to 4.79 g/cm 3 . The alloy with 9 wt.% Cu had the lowest corrosion rate (0.000181 mm/year) and a corrosion current of 19 nA/cm 2 . The cytotoxicity results showed that the Ti–25Nb– x Cu alloys exhibited good biocompatibility with MC-3T3-E1 osteoblast cells, as cell viability values were above 90%. It is important to note that the Ti–25Nb alloy with 9 wt.% copper showed the best combination of microstructure, mechanical properties, and corrosion resistance, and is a potential candidate for medical implant applications.
Förderung
- RIIM LPDP Grant and BRIN
- Research Organization for Nanotechnology and Materials – National Research and Innovation Agency
Zitieren
APA
Sutowo, C., Lestari, A. A., Senopati, G., Hakim, R. N., Syahid, A. N., Annur, D., Triwardono, J., Rokhmanto, F., Riyanto, E., Erryani, A., Setyawan, A. D. H., Thaha, Y. N., Rosyidah, A., Tjahjono, A., & Kartika, I. (2026). Effect of Cu addition on phase evolution, mechanical properties, corrosion behavior, and cytocompatibility of Ti–25Nb alloys fabricated by cold isostatic pressing. Powder Metallurgy. https://doi.org/10.1177/00325899261505087
Vancouver
Sutowo C, Lestari AA, Senopati G, Hakim RN, Syahid AN, Annur D, et al. Effect of Cu addition on phase evolution, mechanical properties, corrosion behavior, and cytocompatibility of Ti–25Nb alloys fabricated by cold isostatic pressing. Powder Metallurgy. 2026. doi:10.1177/00325899261505087
BibTeX
@article{Sutowo2026,
author = {Sutowo, Cahya and Lestari, Amelia Ayu and Senopati, Galih and Hakim, Rahma Nisa and Syahid, Adi Noer and Annur, Dhyah and Triwardono, Joko and Rokhmanto, Fendy and Riyanto, Edy and Erryani, Aprilia and Setyawan, Albertus Deny Heri and Thaha, Yudi Nugraha and Rosyidah, A'liyatur and Tjahjono, Arif and Kartika, Ika},
title = {Effect of Cu addition on phase evolution, mechanical properties, corrosion behavior, and cytocompatibility of Ti–25Nb alloys fabricated by cold isostatic pressing},
journal = {Powder Metallurgy},
year = {2026},
doi = {10.1177/00325899261505087}
}
EUVIMED