EUVIMEDEUVIMED entdecken
Crossref

Effect of CIGS Absorber Thickness on the Performance of In 2 S 3 -Buffered Thin-Film Solar Cells: Role of the MgF 2 Antireflection Coating

Papa Sow, Cheick Goudiaby, Alioune Ngom, Jacques Faye, Ahmed Mohamed-Yahya, Mamadou Samb

Engineering and Applied Sciences · 27.09.2026 · 11 (5) · 164-178

DOI: 10.11648/j.eas.20261105.12 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Engineering and Applied Sciences, online erschienen am 27.09.2026. Verfasst von Papa Sow und 5 weiteren Autor:innen. Die Arbeit nennt 34 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This work numerically investigates, using the Silvaco ATLAS simulator, a thin-film solar cell based on a Cu(In,Ga)Se₂ (CIGS) absorber combined with a non-toxic In 2 S 3 buffer layer replacing conventional CdS, building on an earlier doping-optimization study that identified N A = 3×10 16 cm -3 as optimal for both configurations investigated (with and without a MgF 2 antireflection coating). At this doping level, two otherwise identical structures, one with MgF 2 and one without, are compared to isolate the effect of CIGS absorber thickness (0.5 to 4 µm) on J sc , V oc , FF and η. Efficiency increases monotonically with thickness, reaching 24.7% with MgF 2 and 21.93% without at 4 µm, a nearly constant relative gain of about 12.6% attributable almost entirely to the increase in short-circuit current. The analysis also tracks the effective series (R s ) and shunt (R sh ) resistances extracted from the simulated J–V curves to clarify the mechanism behind the improvement of the fill factor with thickness. The decrease in Rs and increase in R sh are consistent with reduced electrical losses in thicker absorbers, though these values are read as effective electrical descriptors rather than direct proof of a microstructural change, since no grain-boundary or defect-density model was varied with thickness. A marginal-gain analysis of the full thickness interval, combined with a relative active-material-use analysis, identifies 2–3 µm with MgF 2 as the best trade-off between performance and material use. A particularly compact illustration is that a 1 µm CIGS cell with MgF 2 (η = 22.17%) already outperforms a 4 µm cell without MgF 2 (η = 21.93%), using only a quarter of the absorber volume, showing that improved front-surface optical management can compensate for a substantial reduction in absorber thickness.

Zitieren

APA

Sow, P., Goudiaby, C., Ngom, A., Faye, J., Mohamed-Yahya, A., & Samb, M. (2026). Effect of CIGS Absorber Thickness on the Performance of In 2 S 3 -Buffered Thin-Film Solar Cells: Role of the MgF 2 Antireflection Coating. Engineering and Applied Sciences, 11(5), 164-178. https://doi.org/10.11648/j.eas.20261105.12

Vancouver

Sow P, Goudiaby C, Ngom A, Faye J, Mohamed-Yahya A, Samb M. Effect of CIGS Absorber Thickness on the Performance of In 2 S 3 -Buffered Thin-Film Solar Cells: Role of the MgF 2 Antireflection Coating. Engineering and Applied Sciences. 2026;11(5):164-178. doi:10.11648/j.eas.20261105.12

BibTeX
@article{Sow2026,
  author = {Sow, Papa and Goudiaby, Cheick and Ngom, Alioune and Faye, Jacques and Mohamed-Yahya, Ahmed and Samb, Mamadou},
  title = {Effect of CIGS Absorber Thickness on the Performance of In 2 S 3 -Buffered Thin-Film Solar Cells: Role of the MgF 2 Antireflection Coating},
  journal = {Engineering and Applied Sciences},
  year = {2026},
  volume = {11},
  number = {5},
  pages = {164--178},
  doi = {10.11648/j.eas.20261105.12}
}
Kostenlos starten →