EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Joining 1.1‐ and 2.1‐mm Al Sheets by Friction Stir Spot Welding

Isam Tareq Abdullah, Mohanad Kadhim Mejbel, Ammar A. H. Al-Filfily

Material Design & Processing Communication · 2025-01 · 2025 (1)

DOI: 10.1155/mdp2/3110429 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Material Design & Processing Communication, online erschienen am 06.01.2025. Verfasst von Isam Tareq Abdullah und 2 weiteren Autor:innen. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 81 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study used friction stir spot welding (FSSW) to weld 1.1‐ and 2.1‐mm AA6061‐T6 sheets at 560, 710, 900, and 1120 rpm at a fixed dwell duration of 5 s. It was determined how much heat was supplied into the FSSW, and the cycle temperature that occurred throughout the FSSW technique was carefully documented. Both the sheet metals and the formed FSSW weldments were subjected to micro and macrostructure analysis, as well as a lap shear test and a hardness test. A scanning electron microscope (SEM) was also used to study the cracked surfaces. A broad variety of rotation rates, ranging from 560 to 1120 rpm, were used to construct error‐free spot joints, as shown by the macroanalysis. The microstructural results may show acceptable mechanical characteristics of FSSW joints, which pertain to the grain refinement of the joints’ stir zone (SZ). It was discovered that the optimal welding condition for establishing spot welds with varying thicknesses of thin sheets was 710 rpm. This was achieved with a SZ lap shear resistance of 5020 ± 20 N and hardness of 99 ± 2 HV (100) . The temperature fluctuation and Von Mises stress distribution, in the AA6061‐T6 FSSW sheets, were analysed by using ABAQUS/CAE 2021 software. The simulated peak temperature is rather similar to the recorded one. On the other hand, by raising the rotation speed, the peak temperature at the welded joints rose. The friction stir welding (FSW) procedures have an impact on the residual stresses; on the other hand, the welding parameters are influenced by the welding temperature and mixing.

Zitieren

APA

Abdullah, I. T., Mejbel, M. K., & Al-Filfily, A. A. H. (2025). Joining 1.1‐ and 2.1‐mm Al Sheets by Friction Stir Spot Welding. Material Design & Processing Communication, 2025(1). https://doi.org/10.1155/mdp2/3110429

Vancouver

Abdullah IT, Mejbel MK, Al-Filfily AAH. Joining 1.1‐ and 2.1‐mm Al Sheets by Friction Stir Spot Welding. Material Design & Processing Communication. 2025;2025(1). doi:10.1155/mdp2/3110429

BibTeX
@article{Abdullah2025,
  author = {Abdullah, Isam Tareq and Mejbel, Mohanad Kadhim and Al-Filfily, Ammar A. H.},
  title = {Joining 1.1‐ and 2.1‐mm Al Sheets by Friction Stir Spot Welding},
  journal = {Material Design & Processing Communication},
  year = {2025},
  volume = {2025},
  number = {1},
  doi = {10.1155/mdp2/3110429}
}
Kostenlos starten →