Analysis of Influencing Factors on Particle Deposition in Electric Heater With Segmental Baffles
International Journal of Chemical Engineering · 2026-01 · 2026 (1)
DOI: 10.1155/ijce/9739705 ↗Kurz gefasst
Fachartikel in der Zeitschrift International Journal of Chemical Engineering, online erschienen am 29.07.2026. Verfasst von Biyang Feng und 2 weiteren Autor:innen. Die Arbeit nennt 83 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Natural Science Foundation of Gansu Province, Longdong University.
Abstract (Originalsprache)
Against the backdrop of the “dual carbon” goals, electric heaters have been widely deployed on offshore oil and gas platforms. Nevertheless, salt particle deposition inside such equipment severely endangers the stable operation of facilities. Relying on a laboratory dynamic ethylene glycol desalination experimental setup, this paper performs numerical simulations of solid–liquid two‐phase flow inside an electric heater with segmental baffles by adopting the Euler–Euler two‐fluid model coupled with the RNG k‐ε turbulence model in Fluent. A comprehensive performance index h·Δ P −1/3 is introduced to evaluate the thermal and hydraulic performance of heaters with various structural configurations. The effects of inlet and outlet layout, baffle quantity, baffle height, heater installation inclination angle, and particle diameter on particle deposition distribution within the electric heater are systematically investigated. The adopted numerical model is validated against classic literature, which can accurately capture particle transport behaviors in strongly swirling and complex recirculating flow fields. The results reveal that in the original electric heater, particles mainly deposit in the upstream zone in front of the bottom baffles and the bottom area beneath the outlet, and the deposition mass gradually rises along the flow direction. Among four inlet–outlet arrangements, the top‐in and bottom‐out configuration remarkably alleviates particle deposition at the bottom near the outlet and delivers the optimal comprehensive performance. Under the same number of bottom baffles, electric heaters with more total baffles exhibit less particle deposition on the bottom, and such a difference becomes more prominent with fewer baffles. Increasing the number of baffles helps reduce particle deposition around the bottom baffles of the electric heater, while the comprehensive performance first rises and then declines. As the baffle height increases, the solid‐phase volume fraction in the upstream region of the bottom baffles decreases progressively, whereas that in the downstream region increases continuously; the total solid‐phase volume fraction first declines and then grows, and the comprehensive performance rises first, followed by a drop. Increasing the installation inclination angle shifts the particle deposition zone from the baffle region to the rear header of the electric heater. In addition, larger particle diameters lead to more severe particle deposition on the bottom. This study fills the research gap regarding particle deposition inside electric heaters and provides theoretical foundations and design references for mitigating deposition in relevant equipment.
Förderung
- Natural Science Foundation of Gansu Province
- Longdong University
Zitieren
APA
Feng, B., Zhu, P., & Chao, H. (2026). Analysis of Influencing Factors on Particle Deposition in Electric Heater With Segmental Baffles. International Journal of Chemical Engineering, 2026(1). https://doi.org/10.1155/ijce/9739705
Vancouver
Feng B, Zhu P, Chao H. Analysis of Influencing Factors on Particle Deposition in Electric Heater With Segmental Baffles. International Journal of Chemical Engineering. 2026;2026(1). doi:10.1155/ijce/9739705
BibTeX
@article{Feng2026,
author = {Feng, Biyang and Zhu, Pan and Chao, Haowen},
title = {Analysis of Influencing Factors on Particle Deposition in Electric Heater With Segmental Baffles},
journal = {International Journal of Chemical Engineering},
year = {2026},
volume = {2026},
number = {1},
doi = {10.1155/ijce/9739705}
}
EUVIMED