EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Spark Plasma Sintering of Low‐Density Stainless Steel: Optimisation of Sintering Parameters

Dineo Mosoma, Vhonani Munyangane, Rasidi Sule, Desmond Klenam, Moses Avwerosuoghene Okoro, Michael Oluwatosin Bodunrin

Advances in Materials Science and Engineering · 2026-01 · 2026 (1)

DOI: 10.1155/amse/8536362 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advances in Materials Science and Engineering, online erschienen am 24.07.2026. Verfasst von Dineo Mosoma und 5 weiteren Autor:innen. Die Arbeit nennt 77 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The study was conducted to determine the optimised sintering conditions for producing low‐density stainless steel via powder metallurgy route. Low‐density Fe–Mn–Al–Cr–C stainless‐steel alloys containing Mo and Cu were produced from commercially available elemental powders via mechanical alloying followed by consolidation using spark plasma sintering (SPS). Four alloy compositions under varying sintering parameters, including temperature (900°C–1100°C), dwell time (5–7 min) and pressure (40–50 MPa), were explored. Electrochemical testing, including open‐circuit potential (OCP) and cyclic polarisation (CP), was performed in 0.9% NaCl to evaluate corrosion susceptibility. Characterisation of both the mechanically alloyed powders and the sintered alloys was performed using scanning electron microscopy–backscattered electron imaging, scanning electron microscopy–energy‐dispersive X‐ray spectroscopy and X‐ray diffraction. The XRD patterns of the mechanically alloyed powders revealed the presence of two phases, austenite and ferrite, together with the formation of Mo‐enriched precipitates. Results indicated that sintering temperature, pressure and dwell time had a significant effect on the final density, which increased with higher parameter values. The sintered alloys achieved relative densities between approximately 94% and 100%. The porosity ranged from 0.01% to 5%. Microstructural examination indicated that the alloys consist mainly of a duplex configuration made up of γ ‐austenite with an FCC crystal structure and α ‐ferrite with a BCC structure. In addition, precipitates enriched in Cr and Mo were identified particularly in Alloys 3 (Fe–30.67Mn–2.39Al–4.23Cr–0.09C–5.20Mo–3.44Cu wt%) and 4 (Fe–21.55Mn–3.78Al–4.12Cr–0.22C–5.30Mo–3.51Cu wt%). Among all compositions, Alloy 1 (6Fe‐31.49 Mn‐2.45 Al‐4.34 Cr‐0.09 C wt%) demonstrated the best overall sintering response, microstructural quality and corrosion resistance, achieving a high density of 99.4% (Alloy 1C) and a low corrosion rate of 0.087 mm/yr (Alloy 1D). The optimum sintering conditions were determined to be 1100°C and 50 MPa for Alloys 1 (Fe‐31.49Mn‐2.45Al‐4.34Cr‐0.09C wt%) and 2 (Fe‐22.14Mn‐3.88Al‐4.23Cr‐0.23C wt%) and 900°C and 50 MPa for Alloys 3 (Fe‐30.67Mn‐2.39Al‐4.23Cr‐0.09C‐5.20Mo‐3.44Cu wt%) and 4 (Fe‐21.55Mn‐3.78Al‐4.12Cr‐0.22C‐5.30Mo‐3.51Cu wt%).

Zitieren

APA

Mosoma, D., Munyangane, V., Sule, R., Klenam, D., Okoro, M. A., & Bodunrin, M. O. (2026). Spark Plasma Sintering of Low‐Density Stainless Steel: Optimisation of Sintering Parameters. Advances in Materials Science and Engineering, 2026(1). https://doi.org/10.1155/amse/8536362

Vancouver

Mosoma D, Munyangane V, Sule R, Klenam D, Okoro MA, Bodunrin MO. Spark Plasma Sintering of Low‐Density Stainless Steel: Optimisation of Sintering Parameters. Advances in Materials Science and Engineering. 2026;2026(1). doi:10.1155/amse/8536362

BibTeX
@article{Mosoma2026,
  author = {Mosoma, Dineo and Munyangane, Vhonani and Sule, Rasidi and Klenam, Desmond and Okoro, Moses Avwerosuoghene and Bodunrin, Michael Oluwatosin},
  title = {Spark Plasma Sintering of Low‐Density Stainless Steel: Optimisation of Sintering Parameters},
  journal = {Advances in Materials Science and Engineering},
  year = {2026},
  volume = {2026},
  number = {1},
  doi = {10.1155/amse/8536362}
}
Kostenlos starten →