EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experimental Study and Optimization of Electrochemical Machining of Al‐7Si‐0.4Mg Alloy Using NaNO 3 and NaOH Electrolytes

Hari Prasadarao Pydi, Adina Srinivasa Vara Prasad, Movva Naga Swapna Sri, Chitrada Prasad, Anusha Peyyala, Boru Bedeya Jarso, Deepak Gupta, Vijayakumar Sivasundar

Advances in Materials Science and Engineering · 2025-01 · 2025 (1)

DOI: 10.1155/amse/3884745 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advances in Materials Science and Engineering, online erschienen am 30.09.2025. Verfasst von Hari Prasadarao Pydi und 7 weiteren Autor:innen. Die Arbeit wurde bisher 19-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study focused on the electrochemical machining (ECM) of Al‐7Si‐0.4Mg alloy using a mixture electrolyte of NaNO 3 and NaOH. Experiments were designed based on the Taguchi method, utilizing an L16 orthogonal array, and input parameters such as voltage (V), electrolyte concentration (E), feed rate (F) and duty cycle (D) were varied to evaluate the effects on material removal rate (MRR) and surface roughness (SR). Residual analysis, ANOVA and signal‐to‐noise (SN) ratio analysis were conducted to determine the optimal settings for single‐response optimization. For multi‐response optimization, a hybrid statistical approach combining Taguchi and TOPSIS was employed. The Taguchi–TOPSIS combination analysis identified the optimal parameter combination as V4–E3–F2–D3, corresponding to a voltage of 14 V, an electrolyte concentration of 80 g/L, a feed rate of 0.5 mm/min and a duty cycle of 75%, which achieved the highest MRR and lowest SR. ANOVA results revealed that voltage is the most influential factor, contributing 91.3% to MRR and 60.6% for SR. Validation tests under these optimal conditions (V4–E3–F2–D3) yielded an MRR of 33.25 mm 3 /min and a SR of 0.164 μm. Compared to prior experimental results, the optimized parameters achieved through the Taguchi–TOPSIS approach led to a 7.32% increase in MRR and an 11.35% reduction in SR, confirming the reliability and effectiveness of this hybrid method in significantly improving machining performance. Finally, the integration of the hybrid statistical optimization strategy with the dual‐electrolyte formulation made a significant advancement in the ECM of Al alloys, providing a highly efficient and minimal surface damage.

Zitieren

APA

Pydi, H. P., Prasad, A. S. V., Sri, M. N. S., Prasad, C., Peyyala, A., Jarso, B. B., Gupta, D., & Sivasundar, V. (2025). Experimental Study and Optimization of Electrochemical Machining of Al‐7Si‐0.4Mg Alloy Using NaNO 3 and NaOH Electrolytes. Advances in Materials Science and Engineering, 2025(1). https://doi.org/10.1155/amse/3884745

Vancouver

Pydi HP, Prasad ASV, Sri MNS, Prasad C, Peyyala A, Jarso BB, et al. Experimental Study and Optimization of Electrochemical Machining of Al‐7Si‐0.4Mg Alloy Using NaNO 3 and NaOH Electrolytes. Advances in Materials Science and Engineering. 2025;2025(1). doi:10.1155/amse/3884745

BibTeX
@article{Pydi2025,
  author = {Pydi, Hari Prasadarao and Prasad, Adina Srinivasa Vara and Sri, Movva Naga Swapna and Prasad, Chitrada and Peyyala, Anusha and Jarso, Boru Bedeya and Gupta, Deepak and Sivasundar, Vijayakumar},
  title = {Experimental Study and Optimization of Electrochemical Machining of Al‐7Si‐0.4Mg Alloy Using NaNO 3 and NaOH Electrolytes},
  journal = {Advances in Materials Science and Engineering},
  year = {2025},
  volume = {2025},
  number = {1},
  doi = {10.1155/amse/3884745}
}
Kostenlos starten →