Microstructure, Mechanical Properties, and Residual Stress Distribution of AISI 316L Stainless Steel Part Fabricated by Laser Metal Deposition
Scanning · 25.07.2020 · 2020 · 1-10
DOI: 10.1155/2020/4831798 ↗Kurz gefasst
Fachartikel in der Zeitschrift Scanning, erschienen am 25.07.2020. Verfasst von Jiayang Gu und 5 weiteren Autor:innen. Beteiligte Einrichtung: Marine Equipment and Technology Institute, Jiangsu University of Science and Technology, Zhenjiang, Jiangsu 212003, China. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 23 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Royal Society International Exchanges 2018 Cost Share (China) Scheme, Natural Science Foundation of Jiangsu Province, National Natural Science Foundation of China.
Abstract (Originalsprache)
In this paper, AISI 316L stainless steel part is obtained by laser metal deposition additive manufacturing method. The microstructure of the part was observed and analyzed by an optical microscope. The tensile mechanical properties and residual stress distribution of the part were tested by tensile test and the contour method. The results show that the bulk structure is mainly columnar crystal and equiaxed crystal, and the latter layer of laser metal deposition will form a remelted zone and heat-affected zone in the former deposition zone. Tensile test results show that the tensile strength of tensile specimens parallel to laser scanning direction and perpendicular to laser scanning direction is basically the same, but the elongation of the specimens perpendicular to the laser scanning direction is relatively better. The main reason is the different distribution characteristics of columnar crystals and equiaxed crystals in the two directions. Relatively large deformation occurs on the cut surface of the specimen after low-speed wire cut. The residual stress test results indicate that tensile stress is formed in the upper part and it reaches 315 MPa at the top surface. And compressive stress is formed at the part/substrate interface and the substrate.
Autor:innen und Institutionen
- Marine Equipment and Technology Institute, Jiangsu University of Science and Technology, Zhenjiang, Jiangsu 212003, China.
- School of Materials Science and Engineering, Jiangsu University of Science and Technology, Zhenjiang, Jiangsu 212003, China.
- Cardiff School of Engineering, Cardiff University, Cardiff CF24 3AA, UK.
ORCID-Profile: Ruifeng Li
Förderung
- Royal Society International Exchanges 2018 Cost Share (China) Scheme
- Natural Science Foundation of Jiangsu Province
- National Natural Science Foundation of China
- National Key Research and Development Program of China
Zitieren
APA
Gu, J., Li, R., Qiu, Y., Yue, H., Liu, B., & Gu, H. (2020). Microstructure, Mechanical Properties, and Residual Stress Distribution of AISI 316L Stainless Steel Part Fabricated by Laser Metal Deposition. Scanning, 2020, 1-10. https://doi.org/10.1155/2020/4831798
Vancouver
Gu J, Li R, Qiu Y, Yue H, Liu B, Gu H. Microstructure, Mechanical Properties, and Residual Stress Distribution of AISI 316L Stainless Steel Part Fabricated by Laser Metal Deposition. Scanning. 2020;2020:1-10. doi:10.1155/2020/4831798
BibTeX
@article{Gu2020,
author = {Gu, Jiayang and Li, Ruifeng and Qiu, Yi and Yue, Hangyu and Liu, Bin and Gu, Heng},
title = {Microstructure, Mechanical Properties, and Residual Stress Distribution of AISI 316L Stainless Steel Part Fabricated by Laser Metal Deposition},
journal = {Scanning},
year = {2020},
volume = {2020},
pages = {1--10},
doi = {10.1155/2020/4831798}
}
EUVIMED