Optimization of Sustainable Hard Carbon Composite Electrodes for Sodium-Ion Batteries
ECS Meeting Abstracts · 07.07.2026 · MA2026-01 (8) · 733-733
DOI: 10.1149/ma2026-018733mtgabs ↗Kurz gefasst
Fachartikel in der Zeitschrift ECS Meeting Abstracts, erschienen am 07.07.2026. Verfasst von Marion Bermont und 4 weiteren Autor:innen.
Abstract (Originalsprache)
Li-ion batteries are well known and have been used for decades due to their high performance, long lifetime and safety. However, the increasing demand in energy storage devices has brought attention to their high production costs due to the use of critical elements ( lithium, copper, cobalt ) 1 . As an alternative to Li-ion batteries, Na-ion batteries have emerged. This technology allows the use of more abundant elements and the use of Al as current collector. However, the use of graphite as negative electrodes for Na-ion batteries is not possible: the intercalation of Na + between the graphene sheets is limited 2 . Nevertheless, another family of carbons exhibits promising Na storage performances: hard carbons. Indeed, those disordered carbons can deliver a reversible capacity exceeding 300 mAh.g -1 3 . However, they still present some drawbacks. The most critical issue is the low Initial Coulombic Efficiency ( ICE ), which remains below 80% for most of the biomass-derived hard carbons 4 . To improve the ICE, we propose to modify the surface of our hard carbons by soft-carbon coating. Biomass materials ( lignin, tannin ) are here used as precursors for the hard carbon, while the coating is made of soft carbon using petroleum pitch as the precursor. This coating layer is expected to limit the electrolyte decomposition leading to higher ICE. Indeed, soft carbon is a more organised material with fewer heteroatoms and fewer defects which limit the number of active sites for irreversible Na trapping. Hard carbons were first synthesized by direct pyrolysis of the precursor at different temperatures ( between 900°C to 1400°C ). Then, the coating was applied using the impregnation method before a second pyrolysis at 900°C. Different ratios of hard to soft carbon were tested. The specific surface area ( S BET ) of the coated and uncoated samples were characterized by physisorption techniques ( N 2 , CO 2 ) and surface groups were identified thanks to XPS measurements. Electrochemical tests were performed in half-cells. Our best performances are obtained with a lignin for an initial pyrolysis temperature of 1200°C for which a reversible capacity of 310 mAh.g -1 with an ICE of 89% is reached at C/20. Surprisingly, the specific surface area increased with the coating, while the electrochemical performances improved. We will show by XPS spectroscopy the importance of the nature of surface groups on the SEI formation and demonstrate that the carbon surface chemistry is a key parameter in the optimization of hard carbon electrodes. Another aspect of the optimization process of hard carbons is the morphological control of the particles. Indeed, spheres are well known to improve electrochemical performances: they have a higher tapped density and so a higher volumetric capacity. Moreover, the reduced electrode porosity improves the electron transport 5 . The hydrothermal route including glucose as the precursor is the most used one to obtain this morphology. However, the yield is very low ( 10-15% ) and this type of synthesis is time-consuming which implies a high energy consumption 6 . We proposed another way to obtain spheres with our bio-based precursors: the spray-dryer method. This fast process allows the precise control of the particle size. The main challenge is the optimization of each parameter to obtain particles as spherical as possible. In our case, we choose to put our bio-based carbonaceous molecules in water with a base ( KOH, NaOH ) to help the polymerisation process before spray-drying. In order to fix the morphology, a first pyrolysis at low temperature ( 300-600°C ) was performed before the washing step. Then, the final pyrolysis was done at high temperature ( 1200°C or 1400°C ). Different mass ratios between the base and the precursor ( 0-40 wt% ) and different proportion of water ( 20-60 mL ) were tested and their impact on the morphology was studied. Indeed, depending on the chosen parameters, the morphology/particles size was not the same leading to different electrochemical performances. By combining morphological control by the spray-dryer method and soft-carbon coating, we will show that bio-based hard carbons with high performances can be obtained. Their performances in half-cells ( vs. Na ) and full cells ( vs. NVPF ) will be discussed. References: A. Munoz-Marquez et al. Adv. Energy Mater. 2017, 7, 1700463 Moriwake et al. RSC Advances, 2017, 7, 36550 Daher et al. ACS Appl. Energy Mater, 2020, 3, 6501-6510 Tonnoir et al. Materials Today Chemistry, 2022, 23, 100614 Beda et al. J. Mater. Chem. A., 2021, 9, 1743 Li et al. J. Cham. Mater. A, 2014, 3, 71
Zitieren
APA
Bermont, M., Davoisne, C., Viallet, V., Janot, R., & Huo, D. (2026). Optimization of Sustainable Hard Carbon Composite Electrodes for Sodium-Ion Batteries. ECS Meeting Abstracts, MA2026-01(8), 733-733. https://doi.org/10.1149/ma2026-018733mtgabs
Vancouver
Bermont M, Davoisne C, Viallet V, Janot R, Huo D. Optimization of Sustainable Hard Carbon Composite Electrodes for Sodium-Ion Batteries. ECS Meeting Abstracts. 2026;MA2026-01(8):733-733. doi:10.1149/ma2026-018733mtgabs
BibTeX
@article{Bermont2026,
author = {Bermont, Marion and Davoisne, Carine and Viallet, Virginie and Janot, Raphael and Huo, Da},
title = {Optimization of Sustainable Hard Carbon Composite Electrodes for Sodium-Ion Batteries},
journal = {ECS Meeting Abstracts},
year = {2026},
volume = {MA2026-01},
number = {8},
pages = {733--733},
doi = {10.1149/ma2026-018733mtgabs}
}
EUVIMED