EUVIMEDEUVIMED entdecken
Crossref

3D Modeling of Internal Heating by High-Frequency Current for Cylindrical Li-Ion Batteries

Serhat Yesilyurt, Jingchen Ma, Masanori Ishigaki, Jason Siegel, Anna Stefanopoulou

ECS Meeting Abstracts · 07.07.2026 · MA2026-01 (1) · 84-84

DOI: 10.1149/ma2026-01184mtgabs ↗

Kurz gefasst

Fachartikel in der Zeitschrift ECS Meeting Abstracts, erschienen am 07.07.2026. Verfasst von Serhat Yesilyurt und 4 weiteren Autor:innen.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Efficient battery operation in sub-zero climates remains a critical challenge for electric vehicle performance [1]. Conventional external heating methods, such as resistance heaters or liquid water-glycol systems, are often limited by slow heat transfer rates and uneven temperature distributions, which can accelerate cell degradation [2]. Internal preheating, particularly using high frequency alternating current (HF-AC), offers a promising alternative by generating heat directly within the layers of the cell, ensuring faster and more uniform warming. This study presents a full three-dimensional (3D) electromagnetic model developed to analyze the high-frequency impedance and internal power dissipation (heat source) of cylindrical lithium-ion cells at high frequencies, up to 100 MHz. Accurate modeling of the "jellyroll" structure of a cylindrical battery presents significant computational challenges. The jellyroll consists of many overlapping thin layers—anode, cathode, separators, and current collectors. The investigated cell features two tabs: a negative tab at the outermost layer and a positive tab near the jellyroll's midpoint. Resolving these numerous layers requires an extremely fine mesh. The model is constructed using the RF module of COMSOL Multiphysics 6.3, which solves Maxwell’s equations in the frequency domain. In the model, a single coaxial lumped port is used for the current injection between the anode and cathode of the cell, which is placed inside a finite cylindrical domain as shown in Fig. 1a. A highly detailed computational mesh of quadratic finite elements with about 12M degrees of freedom is used to resolve the electromagnetic field and current distribution in the cell layers, tabs, and the casing. The domain boundaries and the cylindrical connectors between the outer cylinder and the battery are assumed to be perfect electric conductors. To alleviate the effects of the finite domain size on the imaginary part of the impedance at high frequencies, a “de-embedding procedure”—similar to the one commonly used in experimental methods [3]—was adopted. This involved substituting the battery with a virtual copper cylinder to quantify the outer domain and boundary-induced impedance, which is subtracted from the model's impedance results and replaced with the copper cylinder's known impedance (inductance of 21.7 nH) [3]. The de-embedded simulation results match the experimental behavior of the high-frequency impedance of an LFP cell up to 100 MHz (Fig. 1c,d). Excellent agreement with experimental resistance values was observed up to 15 MHz (Fig. 1c). The 3D model provides critical insight into the power dissipation that lower-dimensional models cannot capture. Simulation results reveal that power dissipation is highest in the electrolyte layers at all frequencies (Fig. 1e), followed by the anode layers, where dissipation becomes significant only at high frequencies (50 MHz and above). This indicates that the proximity effect is more dominant than the skin effect at those frequencies. Finally, Fig. 1f shows the electrolyte's dissipation profile with respect to the radial position; it is concentrated between the tabs, saturated at frequencies above 10 MHz, and exhibits a fluctuating pattern that indicates resonance behavior at 100 MHz. This 3D model demonstrates significant utility for analyzing loss concentrations and field distributions in the electrolyte, electrodes and current collectors. By resolving these high-frequency effects (resistance of the electrolyte, skin, and proximity effects), the model directly supports the experimental validation of a rapid, uniform heating protocol that is safe and effective for warming the cell without compromising the state-of-health. REFERENCES Ruan, H., Barreras, J. V., Steinhardt, M., Jossen, A., Offer, G. J., & Wu, B. Journal of Power Sources , 581 , 233484, (2023). Ji, Y., & Wang, C. Y. Electrochimica Acta , 107 , 664-674, (2013). Landinger, T. F., Schwarzberger, G., & Jossen, A. In 2019 IEEE International Symposium on Electromagnetic Compatibility, Signal & Power Integrity (EMC+ SIPI) (pp. 106-110). IEEE, (2019) Figure 1

Zitieren

APA

Yesilyurt, S., Ma, J., Ishigaki, M., Siegel, J., & Stefanopoulou, A. (2026). 3D Modeling of Internal Heating by High-Frequency Current for Cylindrical Li-Ion Batteries. ECS Meeting Abstracts, MA2026-01(1), 84-84. https://doi.org/10.1149/ma2026-01184mtgabs

Vancouver

Yesilyurt S, Ma J, Ishigaki M, Siegel J, Stefanopoulou A. 3D Modeling of Internal Heating by High-Frequency Current for Cylindrical Li-Ion Batteries. ECS Meeting Abstracts. 2026;MA2026-01(1):84-84. doi:10.1149/ma2026-01184mtgabs

BibTeX
@article{Yesilyurt2026,
  author = {Yesilyurt, Serhat and Ma, Jingchen and Ishigaki, Masanori and Siegel, Jason and Stefanopoulou, Anna},
  title = {3D Modeling of Internal Heating by High-Frequency Current for Cylindrical Li-Ion Batteries},
  journal = {ECS Meeting Abstracts},
  year = {2026},
  volume = {MA2026-01},
  number = {1},
  pages = {84--84},
  doi = {10.1149/ma2026-01184mtgabs}
}
Kostenlos starten →