Surface Engineering of rGO/Chitosan-Based Artificial Interface Layer on Zn Anode for Stable Aqueous Zn-Ion Batteries
ECS Meeting Abstracts · 07.07.2026 · MA2026-01 (1) · 80-80
DOI: 10.1149/ma2026-01180mtgabs ↗Kurz gefasst
Fachartikel in der Zeitschrift ECS Meeting Abstracts, erschienen am 07.07.2026. Verfasst von Suyeon Kim und 6 weiteren Autor:innen.
Abstract (Originalsprache)
As the global transition toward sustainable energy systems accelerates, the development of safe, cost-effective, and environmentally sustainable energy storage technologies has become increasingly important. To mitigate the intermittency of renewable energy sources, such as solar and wind power, and enable their reliable integration into the power grid, energy storage systems capable of stable operation under diverse conditions are essential. Although lithium-ion batteries dominate the current market, concerns regarding limited lithium resources, high manufacturing costs, and safety risks associated with flammable organic electrolytes have motivated growing interest in alternative batteries. Among the emerging candidates, aqueous Zn-ion batteries (AZIBs) have attracted considerable attention as promising alternatives for stationary energy storage systems. The use of aqueous electrolytes provides AZIBs with inherent safety advantages, making them particularly suitable for large-scale and safety-critical applications. Metallic Zn is an appealing anode material owing to its natural abundance, low cost, high theoretical capacity (820 mAh g -1 ), and relatively low electrochemical potential (-0.762 V vs. SHE). However, the practical deployment of AZIBs is severely hindered by the intrinsic instability of Zn metal anodes. During repeated Zn plating/stripping processes, dendrite growth and parasitic reactions, including the hydrogen evolution reaction (HER) and surface corrosion, occur readily, resulting in degraded electrochemical reversibility and poor long-term operational stability. In particular, uncontrolled Zn dendrite growth can penetrate the separator and induce internal short circuits, leading to rapid capacity fading, cell failure, and serious safety risks. To address these challenges, interfacial engineering of Zn metal anodes through the introduction of protective layers has emerged as an effective strategy. An ideal protective layer should regulate Zn²⁺ ion transport without impeding electrochemical kinetics, suppress undesirable side reactions, and maintain stable interfacial contact with the Zn anode. In this study, we propose a reduced graphene oxide (rGO)/chitosan hybrid protective layer on a Zn metal anode for AZIBs. Chitosan, a bio-polymer obtained from natural chitin, contains abundant amino and hydroxyl groups that exhibit strong chemical affinities for Zn 2+ ions. In the rGO/chitosan hybrid structure, chitosan was homogeneously intercalated between the rGO sheets, suppressing rGO restacking and facilitating uniform interfacial ion coordination. Benefiting from the synergistic combination of the high mechanical strength and electrical conductivity of rGO with the strong Zn 2+ ion affinity of chitosan, the rGO/chitosan protective layer enabled uniform ionic coordination and regulated Zn 2+ ion flux at the electrode-electrolyte interface. Electrochemical characterization demonstrated that the Zn anodes protected by the rGO/chitosan layer exhibited significantly improved interfacial behavior. The Zn@rGO/chitosan anode showed a significantly reduced Zn nucleation overpotential of 27 mV compared to 53 mV for bare Zn, indicating facilitated and more uniform Zn nucleation. In addition, the rGO/chitosan layer effectively suppressed HER. The HER onset potential measured at a current density of 10 mA cm -2 shifted from -1.72 V (vs. Ag/AgCl) for bare Zn to -1.84 V (vs. Ag/AgCl) for Zn@rGO/chitosan, indicating reduced parasitic reactions and enhanced interfacial stability. In the symmetric cell test conducted at a current density of 1 mA cm -2 with an areal capacity of 1 mAh cm -2 , bare Zn suffered from an early short-circuit failure after 110 h, whereas Zn@rGO exhibited slightly improved stability, with a short-circuit occurring at 180 h. In contrast, Zn@rGO/chitosan maintained stable and reversible plating/stripping behavior for 850 h, reflecting substantially enhanced cycle stability. Furthermore, the full cells assembled with an α-MnO 2 cathode delivered a high initial discharge capacity of 332 mAh g -1 at 0.1 A g -1 , confirming the practical performance enhancement provided by the hybrid protective layer. Overall, these results demonstrate that the rGO/chitosan hybrid protective layer effectively stabilizes the Zn metal anode interface and provides valuable insights into interfacial design strategies to improve the long-term stability of AZIBs.
Zitieren
APA
Kim, S., Chhetri, K., Gudal, C. C., Baek, S. R., Lee, H., Lee, S., & Chung, C. (2026). Surface Engineering of rGO/Chitosan-Based Artificial Interface Layer on Zn Anode for Stable Aqueous Zn-Ion Batteries. ECS Meeting Abstracts, MA2026-01(1), 80-80. https://doi.org/10.1149/ma2026-01180mtgabs
Vancouver
Kim S, Chhetri K, Gudal CC, Baek SR, Lee H, Lee S, et al. Surface Engineering of rGO/Chitosan-Based Artificial Interface Layer on Zn Anode for Stable Aqueous Zn-Ion Batteries. ECS Meeting Abstracts. 2026;MA2026-01(1):80-80. doi:10.1149/ma2026-01180mtgabs
BibTeX
@article{Kim2026,
author = {Kim, Suyeon and Chhetri, Kisan and Gudal, Chandan Chandru and Baek, Seung Ryong and Lee, Harin and Lee, Somi and Chung, Chan-Hwa},
title = {Surface Engineering of rGO/Chitosan-Based Artificial Interface Layer on Zn Anode for Stable Aqueous Zn-Ion Batteries},
journal = {ECS Meeting Abstracts},
year = {2026},
volume = {MA2026-01},
number = {1},
pages = {80--80},
doi = {10.1149/ma2026-01180mtgabs}
}
EUVIMED