EUVIMEDEUVIMED entdecken
Crossref

Improving Subsequent Counter-Rotating Electrochemical Machining of TA15 Alloy by Laser Depassivation: Role of Scanning Speed and Overlap Rate

Dongbao Wang, Dengyong Wang, Feng Cao

Journal of The Electrochemical Society · 28.08.2026 · 173 (16) · 163502

DOI: 10.1149/1945-7111/ae97bd ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of The Electrochemical Society, online erschienen am 19.08.2026. Verfasst von Dongbao Wang und 2 weiteren Autor:innen. Die Arbeit nennt 47 Literaturangaben. Gefördert von: Fundamental Research Funds for the Central Universities, National Natural Science Foundation of China, Postgraduate Research & Practice Innovation Program of Jiangsu Province.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The passivation films formed during electrochemical machining (ECM) of titanium alloys hinder charge transfer, suppress continuous anodic dissolution and destabilize subsequent machining. This study investigated laser depassivation of ECM-treated TA15 alloy surfaces at a fixed laser energy density. The scanning speed was varied from 500 to 15 000 mm s −1 , corresponding to spot overlap rates from 93.75% to −87.5%. The electrochemical measurements, chemical analyses, and TEM were used to correlate laser-treated surface states with subsequent counter-rotating electrochemical machining (CRECM) performance. The untreated ECM surface and the surfaces treated at low scanning speeds remained dominated by passivation film-controlled responses. Low scanning speeds with high overlap rates partially removed the original film but induced remelting, cracking and thermal reoxidation, increasing the oxygen content to 18.09% at 500 mm s −1 . At 6000 mm s −1 with 25% overlap rate, passivation products were effectively reduced while thermal damage was limited, obtaining the lowest oxygen content of 2.18%. Excessively high scanning speeds caused insufficient laser coverage and incomplete depassivation. TEM confirmed that the 146.3 nm ECM-induced film was almost completely removed after laser treatment, with the oxygen content decreasing to about 1.38%. Subsequent CRECM showed that the local profile roughness R a was 89.692 ± 2.316 μm without laser depassivation, whereas it remained at 2.174 ± 0.113 μm after laser treatment at 6000 mm s −1 .

Förderung

  • Fundamental Research Funds for the Central Universities
  • National Natural Science Foundation of China
  • Postgraduate Research & Practice Innovation Program of Jiangsu Province

Zitieren

APA

Wang, D., Wang, D., & Cao, F. (2026). Improving Subsequent Counter-Rotating Electrochemical Machining of TA15 Alloy by Laser Depassivation: Role of Scanning Speed and Overlap Rate. Journal of The Electrochemical Society, 173(16), 163502. https://doi.org/10.1149/1945-7111/ae97bd

Vancouver

Wang D, Wang D, Cao F. Improving Subsequent Counter-Rotating Electrochemical Machining of TA15 Alloy by Laser Depassivation: Role of Scanning Speed and Overlap Rate. Journal of The Electrochemical Society. 2026;173(16):163502. doi:10.1149/1945-7111/ae97bd

BibTeX
@article{Wang2026,
  author = {Wang, Dongbao and Wang, Dengyong and Cao, Feng},
  title = {Improving Subsequent Counter-Rotating Electrochemical Machining of TA15 Alloy by Laser Depassivation: Role of Scanning Speed and Overlap Rate},
  journal = {Journal of The Electrochemical Society},
  year = {2026},
  volume = {173},
  number = {16},
  pages = {163502},
  doi = {10.1149/1945-7111/ae97bd}
}
Kostenlos starten →