EUVIMEDEUVIMED entdecken
Crossref

Ultrauniform, strong, and ductile 3D-printed titanium alloy through bifunctional alloy design

Jingqi Zhang iD, Michael J Bermingham iD, Joseph Otte iD, Yingang Liu iD, Ziyong Hou iD, Nan Yang iD, Yu Yin iD, Mohamad Bayat iD, Weikang Lin iD, Xiaoxu Huang iD, David H StJohn, Matthew S Dargusch iD

Science · 09.02.2024 · 383 (6683) · 639-645

DOI: 10.1126/science.adj0141 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Science, erschienen am 09.02.2024. Verfasst von Jingqi Zhang und 11 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical and Mining Engineering, The University of Queensland, St. Lucia, Brisbane, QLD, Australia. Die Arbeit wurde bisher 222-mal zitiert (Crossref) und nennt 72 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Coarse columnar grains and heterogeneously distributed phases commonly form in metallic alloys produced by three-dimensional (3D) printing and are often considered undesirable because they can impart nonuniform and inferior mechanical properties. We demonstrate a design strategy to unlock consistent and enhanced properties directly from 3D printing. Using Ti−5Al−5Mo−5V−3Cr as a model alloy, we show that adding molybdenum (Mo) nanoparticles promotes grain refinement during solidification and suppresses the formation of phase heterogeneities during solid-state thermal cycling. The microstructural change because of the bifunctional additive results in uniform mechanical properties and simultaneous enhancement of both strength and ductility. We demonstrate how this alloy can be modified by a single component to address unfavorable microstructures, providing a pathway to achieve desirable mechanical characteristics directly from 3D printing.

Autor:innen und Institutionen

  • School of Mechanical and Mining Engineering, The University of Queensland, St. Lucia, Brisbane, QLD, Australia.
  • Centre for Microscopy and Microanalysis, The University of Queensland, St. Lucia, Brisbane, QLD, Australia.
  • International Joint Laboratory for Light Alloys (Ministry of Education), College of Materials Science and Engineering, Chongqing University, Chongqing, China.
  • Shenyang National Laboratory for Materials Science, Chongqing University, Chongqing, China.
  • Department of Materials Science and Engineering, KTH Royal Institute of Technology, Stockholm, Sweden.
  • Department of Mechanical Engineering, Technical University of Denmark, Lyngby, Denmark.

ORCID-Profile: Jingqi Zhang, Michael J Bermingham, Joseph Otte, Yingang Liu, Ziyong Hou, Nan Yang, Yu Yin, Mohamad Bayat, Weikang Lin, Xiaoxu Huang, Matthew S Dargusch

Zitieren

APA

Zhang, J., Bermingham, M. J., Otte, J., Liu, Y., Hou, Z., Yang, N., Yin, Y., Bayat, M., Lin, W., Huang, X., StJohn, D. H., & Dargusch, M. S. (2024). Ultrauniform, strong, and ductile 3D-printed titanium alloy through bifunctional alloy design. Science, 383(6683), 639-645. https://doi.org/10.1126/science.adj0141

Vancouver

Zhang J, Bermingham MJ, Otte J, Liu Y, Hou Z, Yang N, et al. Ultrauniform, strong, and ductile 3D-printed titanium alloy through bifunctional alloy design. Science. 2024;383(6683):639-645. doi:10.1126/science.adj0141

BibTeX
@article{Zhang2024,
  author = {Zhang, Jingqi and Bermingham, Michael J and Otte, Joseph and Liu, Yingang and Hou, Ziyong and Yang, Nan and Yin, Yu and Bayat, Mohamad and Lin, Weikang and Huang, Xiaoxu and StJohn, David H and Dargusch, Matthew S},
  title = {Ultrauniform, strong, and ductile 3D-printed titanium alloy through bifunctional alloy design},
  journal = {Science},
  year = {2024},
  volume = {383},
  number = {6683},
  pages = {639--645},
  doi = {10.1126/science.adj0141}
}
Kostenlos starten →