Flow-induced orientation and stress-induced reorientation of semicrystalline PBT-based vitrimers
Journal of Rheology · 01.07.2026 · 70 (4) · 831-846
DOI: 10.1122/8.0001141 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Rheology, online erschienen am 11.05.2026. Verfasst von Quentin-Arthur Poutrel und 5 weiteren Autor:innen. Die Arbeit nennt 82 Literaturangaben. Gefördert von: ICEEL Carnot Institute, EMPP research department of Lorraine University.
Abstract (Originalsprache)
The microstructure and deformation mechanisms of polybutylene terephthalate (PBT)-based vitrimer samples produced by injection molding were characterized in a 120–180 °C temperature range through tensile tests calibrated by image correlation, coupled with in situ synchrotron x-ray scattering. Vitrimerization was achieved by an 8 min melt-mixing step followed by injection. Flow-induced orientation of polymer chains after injection strongly depends on the cross-linker content [diglycidyl ether of bisphenol A (DGEBA)]. Up to 0.5 wt. %, the crystallized polymers exhibit almost no orientation. Above 1.0 wt. %, a pronounced shish-kebab morphology emerges, with little further variation at higher DGEBA contents. Lamellae (kebabs) are initially perpendicular to the injection direction, while within the lamellae, the chain axis (c axis) is tilted, as shown by an ∼28° angle between the c* axis and the injection direction. Under tension, polymer chains realign along the stretching direction (35° angle between c* and tensile direction), leading to fibrillar morphology. Increasing cross-linking slows down chain relaxation, as reflected in a Weissenberg number greater than unity during injection—a condition favorable for retaining orientation in the crystalline phase. Unlike typical injection-molded polymers, orientation is observed throughout the entire 4 mm specimen thickness, not only in the skin. Tensile properties strongly correlate with flow-induced orientation. Temperature rise modifies the mechanism of lamellar destruction during deformation: At lower temperatures, crystal fragmentation and reorientation dominate, while at higher temperatures, crystal melting and rapid recrystallization occur. PBT-based vitrimers exhibit the same polymorphic transitions as pristine PBT, specifically the stress-induced α → β transformation and the emergence of a smectic phase during fibrillar morphology development.
Förderung
- ICEEL Carnot Institute
- EMPP research department of Lorraine University
Zitieren
APA
Poutrel, Q., Boisse, J., Hoppe, S., André, S., Tournilhac, F., & Farge, L. (2026). Flow-induced orientation and stress-induced reorientation of semicrystalline PBT-based vitrimers. Journal of Rheology, 70(4), 831-846. https://doi.org/10.1122/8.0001141
Vancouver
Poutrel Q, Boisse J, Hoppe S, André S, Tournilhac F, Farge L. Flow-induced orientation and stress-induced reorientation of semicrystalline PBT-based vitrimers. Journal of Rheology. 2026;70(4):831-846. doi:10.1122/8.0001141
BibTeX
@article{Poutrel2026,
author = {Poutrel, Quentin-Arthur and Boisse, Julien and Hoppe, Sandrine and André, Stéphane and Tournilhac, François and Farge, Laurent},
title = {Flow-induced orientation and stress-induced reorientation of semicrystalline PBT-based vitrimers},
journal = {Journal of Rheology},
year = {2026},
volume = {70},
number = {4},
pages = {831--846},
doi = {10.1122/8.0001141}
}
EUVIMED