EUVIMEDEUVIMED entdecken
Crossref

Design of a large nonevaporable getter pump for the full size ITER beam source prototype

E. Sartori, M. Siragusa, G. Berton, C. Cavallini, S. Dal Bello, M. Fadone, L. Grando, D. Marcuzzi, D. Rizzetto, G. Serianni, P. Sonato, M. Zaupa und 6 weitere

Journal of Vacuum Science & Technology B · 01.05.2023 · 41 (3)

DOI: 10.1116/6.0002395 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Vacuum Science & Technology B, online erschienen am 27.04.2023. Verfasst von E. Sartori und 17 weiteren Autor:innen. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 25 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

An improvement for the vacuum system of the multidriver radio frequency (RF) prototype negative ion source SPIDER has been developed, to allow operating at high RF power, while minimizing the breakdown probability on the outside of the plasma source. A first-of-its-kind large nonevaporable getter (NEG) pump, based on a modular design of 384 cartridges totaling about 350 kg of ZAO® alloy (composed by Zr-Ti-V-Al) with an installed pumping speed at a room temperature of 330 m3/s for hydrogen, will complement the existing pumping system, based on eight cryogenic pumps and four turbomolecular pumps totaling about 90 m3/s in hydrogen. The vessel pressure during absorption is expected to be between 20 and 40 mPa, while during the getter regeneration, the peak operating pressure will be around 2 Pa. The NEG pump will use an additional vessel module, with integrated thermal shields to protect the in-vessel components during activation and regeneration of the pump, to be carried out at temperatures in the range of 550–600 °C. Integrated thermal analyses were carried out to verify the low heat load on pre-existing in-vessel components with a low limit of acceptable temperature, and to provide boundary conditions for the mechanical verifications of the pump structure. The scenario of cyclic hydrogen load was calculated considering the SPIDER operation modes, the expected gas throughput, and the cumulated load to the pump, to determine the regeneration temperature and auxiliary pumping necessary to make the regeneration duration compatible with the high availability of the system. The upgrade of the auxiliary pumping system is also described, as well as the mitigation of air or water exposure risk during regeneration of the NEG pump.

Zitieren

APA

Sartori, E., Siragusa, M., Berton, G., Cavallini, C., Bello, S. D., Fadone, M., Grando, L., Marcuzzi, D., Rizzetto, D., Serianni, G., Sonato, P., Zaupa, M., Dinh, F., Ferrara, A., Maccallini, E., Mura, M., Siviero, F., & Toigo, V. (2023). Design of a large nonevaporable getter pump for the full size ITER beam source prototype. Journal of Vacuum Science & Technology B, 41(3). https://doi.org/10.1116/6.0002395

Vancouver

Sartori E, Siragusa M, Berton G, Cavallini C, Bello SD, Fadone M, et al. Design of a large nonevaporable getter pump for the full size ITER beam source prototype. Journal of Vacuum Science & Technology B. 2023;41(3). doi:10.1116/6.0002395

BibTeX
@article{Sartori2023,
  author = {Sartori, E. and Siragusa, M. and Berton, G. and Cavallini, C. and Bello, S. Dal and Fadone, M. and Grando, L. and Marcuzzi, D. and Rizzetto, D. and Serianni, G. and Sonato, P. and Zaupa, M. and Dinh, F. and Ferrara, A. and Maccallini, E. and Mura, M. and Siviero, F. and Toigo, V.},
  title = {Design of a large nonevaporable getter pump for the full size ITER beam source prototype},
  journal = {Journal of Vacuum Science & Technology B},
  year = {2023},
  volume = {41},
  number = {3},
  doi = {10.1116/6.0002395}
}
Kostenlos starten →