Sponge-Inspired 3D-Printed Lattice Biosensors for Wearable Pressure Sensing
Journal of Manufacturing Science and Engineering · 01.10.2026 · 148 (10)
DOI: 10.1115/1.4071853 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Manufacturing Science and Engineering, online erschienen am 30.06.2026. Verfasst von Huangyi Qu und 4 weiteren Autor:innen. Die Arbeit nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Guangdong Science and Technology Department, Research Grants Council, University Grants Committee.
Abstract (Originalsprache)
Flexible pressure sensors are essential components in modern biosensing platforms, enabling real-time monitoring of mechanical stimuli in wearable health systems, human–machine interfaces, and soft robotic skins. Currently, most flexible pressure sensors enhance performance by optimizing material composition and fabrication processes, while systematic and comparative studies on the influence of internal structure remain relatively limited. Existing sensor architectures are predominantly planar or bulk in form, neglecting the impact of three-dimensional geometries on strain distribution, electrical response, and mechanical reliability. To address this gap, this article draws design inspiration from natural marine sponges, reporting a flexible pressure sensor featuring a bio-inspired scaffold structure. The sensor employs a porous soft lattice resembling sponge skeletons, endowing it with high compressibility and elasticity. Through systematic design and finite element simulation of various lattice shapes, the influence of unit-cell lattice structures on sensor sensitivity is verified. Simulation results indicate that compared to P, G, and IWP-type triply periodic minimal surfaces (TPMS) structures, the D-type TPMS structure exhibits optimal sensitivity, reaching 11.3468%. These simulation results confirm the effectiveness of this design methodology. The sensor is fabricated through a sacrificial molding process. A water-soluble polyvinyl alcohol (PVA) mold of the optimal scaffold design is 3D-printed, and then a conductive silicone elastomer is cast into the mold. After thermal curing, the PVA mold is dissolved in water to yield the standalone conductive silicone scaffold. Electrical testing indicates that sensors with different lattice geometries exhibit varying sensitivities. Compared to TPMS structures with P, G, and IWP-type surfaces, the TPMS structure with a D-type surface demonstrates optimal sensitivity, reaching up to 9.28% in experiments. This further validates the accuracy of the simulation and the effectiveness of the structural design. Finally, we fabricate the sensors into wearable devices and demonstrate their application as pressure sensors. This work demonstrates that the design of a sensor's internal spatial structure is a critical factor determining sensor performance, alongside material selection and fabrication techniques. It offers a promising strategy for optimizing the performance of flexible sensors in wearable and biomedical applications.
Förderung
- Guangdong Science and Technology Department
- Research Grants Council, University Grants Committee
Zitieren
APA
Qu, H., Dong, B., Liu, S., Cai, Y., & Lu, Y. (2026). Sponge-Inspired 3D-Printed Lattice Biosensors for Wearable Pressure Sensing. Journal of Manufacturing Science and Engineering, 148(10). https://doi.org/10.1115/1.4071853
Vancouver
Qu H, Dong B, Liu S, Cai Y, Lu Y. Sponge-Inspired 3D-Printed Lattice Biosensors for Wearable Pressure Sensing. Journal of Manufacturing Science and Engineering. 2026;148(10). doi:10.1115/1.4071853
BibTeX
@article{Qu2026,
author = {Qu, Huangyi and Dong, Bin and Liu, Shishuo and Cai, Yi and Lu, Yanglong},
title = {Sponge-Inspired 3D-Printed Lattice Biosensors for Wearable Pressure Sensing},
journal = {Journal of Manufacturing Science and Engineering},
year = {2026},
volume = {148},
number = {10},
doi = {10.1115/1.4071853}
}
EUVIMED