EUVIMEDEUVIMED entdecken
Validierungsstudie

Verification and Validation of Microcomputed Tomography-Based Analyses of Bone Morphology, Apparent Elastic Modulus, and Von Mises Stress

Mahsa Zojaji, Baixuan Yang, Heidi-Lynn Ploeg iD

Journal of Biomechanical Engineering · 2025

DOI: 10.1115/1.4069110 ↗

Kurz gefasst

Validierungsstudie in der Zeitschrift Journal of Biomechanical Engineering, 2025. Verfasst von Mahsa Zojaji und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical and Materials Engineering, Smith Engineering, Queen's University, Kingston, ON K7L 2V9, Canada; Centre for Health Innovation…. Hauptthemen laut MEDLINE: X-Ray Microtomography, Stress, Mechanical, Elastic Modulus, Cancellous Bone. Die Arbeit nennt 78 Literaturangaben. Gefördert von: NIH HHS, Natural Sciences and Engineering Research Council of Canada, National Institutes of Health.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Patient-specific image-based finite element analysis (FEA) offers a noninvasive method to estimate bone stiffness and strength, but its clinical translation requires thorough verification and validation. While previous studies provide resolution-dependent errors in trabecular bone morphometric indices, there remains a need to extend these analyses to include mechanical property predictions. This study examined microcomputed tomography (μCT) voxel size effects on trabecular bone morphometric analyses and predictions of apparent elastic modulus (Eapp) and trabecular stress. Voxel (v)- and geometry (g)-based FEA of trabecular bone cores under compression were compared. Convergence analyses were performed on element size and boundary conditions; and, bulk density, tissue density, and FEA were validated against experimental measurements. Trabecular bovine bone cores (n = 22, Ø10 mm × 10 mm) were tested quasi-statically under uni-axial compression below the yield limit, and μCT scanned with isotropic voxel sizes of 20 μm, 50 μm, and 100 μm. Increasing voxel size resulted in significant reductions in connectivity density, anisotropy, and trabecular number, while trabecular thickness increased. Predicted Eapp from both v-FEA and g-FEA were highly correlated with measurements (R2 = 0.8, p < 0.001). A maximum mean error of +6.35% was found in Eapp with 100 μm voxel size. Despite its high computational cost (∼120 min), 20 μm v-FEA was the most accurate for predicting Eapp and trabecular stress. Alternatively, both 50 μm v-FEA and g-FEA at low mesh density (h = 0.0011, where h is 1/√number of elements) predicted both Eapp and trabecular stress behavior with less than ±5% error in 10–20 min. Findings support efficient, accurate FEA strategies for predicting trabecular bone mechanics.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

X-Ray MicrotomographyStress, MechanicalElastic ModulusCancellous BoneAnimalsCattleFinite Element Analysis

Autor:innen und Institutionen

  • Department of Mechanical and Materials Engineering, Smith Engineering, Queen's University, Kingston, ON K7L 2V9, Canada; Centre for Health Innovation, Kingston Health Sciences Centre, Queen's University, Kingston, ON K7…
  • Queen's University.

ORCID-Profile: Heidi-Lynn Ploeg

Förderung

  • NIH HHS
  • Natural Sciences and Engineering Research Council of Canada
  • National Institutes of Health

Zitieren

APA

Zojaji, M., Yang, B., & Ploeg, H. L. (2025). Verification and Validation of Microcomputed Tomography-Based Analyses of Bone Morphology, Apparent Elastic Modulus, and Von Mises Stress. Journal of Biomechanical Engineering. https://doi.org/10.1115/1.4069110

Vancouver

Zojaji M, Yang B, Ploeg HL. Verification and Validation of Microcomputed Tomography-Based Analyses of Bone Morphology, Apparent Elastic Modulus, and Von Mises Stress. Journal of Biomechanical Engineering. 2025. doi:10.1115/1.4069110

BibTeX
@article{Zojaji2025,
  author = {Zojaji, Mahsa and Yang, Baixuan and Ploeg, Heidi-Lynn},
  title = {Verification and Validation of Microcomputed Tomography-Based Analyses of Bone Morphology, Apparent Elastic Modulus, and Von Mises Stress},
  journal = {Journal of Biomechanical Engineering},
  year = {2025},
  doi = {10.1115/1.4069110}
}
Kostenlos starten →