EUVIMEDEUVIMED entdecken
Open Access

An Approach to Quantify Anisotropic Multiaxial Failure of the Annulus Fibrosus

Jill M Middendorf iD, Victor H Barocas

Journal of Biomechanical Engineering · 01.01.2024 · 146 (1)

DOI: 10.1115/1.4063822 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomechanical Engineering, online erschienen am 10.11.2023. Verfasst von Jill M Middendorf und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Johns Hopkins University, Baltimore, MD 21218. Hauptthemen laut MEDLINE: Annulus Fibrosus, Intervertebral Disc. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar. Gefördert von: NCCIH NIH HHS.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Tears in the annulus fibrosus (AF) of the intervertebral disk (IVD) occur due to multiaxial loading on the spine. However, most existing AF failure studies measure uniaxial stress, not the multiaxial stress at failure. Delamination theory, which requires advanced structural knowledge and knowledge about the interactions between the AF fibers and matrix, has historically been used to understand and predict AF failure. Alternatively, a simple method, the Tsai-Hill yield criteria, could describe multiaxial failure of the AF. This yield criteria uses the known tissue fiber orientation and an equation to establish the multiaxial failure stresses that cause failure. This paper presents a method to test the multiaxial failure stress of the AF experimentally and evaluate the potential for the Tsai-Hill model to predict these failure stresses. Porcine AF was cut into a dogbone shape at three distinct angles relative to the primary lamella direction (parallel, transverse, and oblique). Then, each dogbone was pulled to complete rupture. The Cauchy stress in the material's fiber coordinates was calculated. These multiaxial stress parameters were used to optimize the coefficients of the Tsai-Hill yield. The coefficients obtained for the Tsai-Hill model vary by an order of magnitude between the fiber and transverse directions, and these coefficients provide a good description of the AF multiaxial failure stress. These results establish both an experimental approach and the use of the Tsai-Hill model to explain the anisotropic failure behavior of the tissue.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Annulus FibrosusIntervertebral DiscAnimalsSwineStress, MechanicalAnisotropy

Stichwörter der Autor:innen

Tsai-Hillannulus fibrosusfailureintervertebral disk

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Johns Hopkins University, Baltimore, MD 21218.
  • Department of Biomedical Engineering, University of Minnesota, Minneapolis, MN 55455.

ORCID-Profile: Jill M Middendorf

Förderung

  • NCCIH NIH HHS

Zitieren

APA

Middendorf, J. M., & Barocas, V. H. (2024). An Approach to Quantify Anisotropic Multiaxial Failure of the Annulus Fibrosus. Journal of Biomechanical Engineering, 146(1). https://doi.org/10.1115/1.4063822

Vancouver

Middendorf JM, Barocas VH. An Approach to Quantify Anisotropic Multiaxial Failure of the Annulus Fibrosus. Journal of Biomechanical Engineering. 2024;146(1). doi:10.1115/1.4063822

BibTeX
@article{Middendorf2024,
  author = {Middendorf, Jill M and Barocas, Victor H},
  title = {An Approach to Quantify Anisotropic Multiaxial Failure of the Annulus Fibrosus},
  journal = {Journal of Biomechanical Engineering},
  year = {2024},
  volume = {146},
  number = {1},
  doi = {10.1115/1.4063822}
}
Kostenlos starten →