EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Ex vivo biomechanical testing of a three‐dimensional printed titanium plate and spacer construct and 4.5 mm locking compression plate for ventral cervical fusion of C4 – C5 in the horse

Steven Zedler, Chantelle Jukic, Andrew van Eps, Darko Stefanovski, Martin Genton, Fabrice Rossignol

Veterinary Surgery · 2025

DOI: 10.1111/vsu.70014 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Veterinary Surgery, 2025. Verfasst von Steven Zedler und 5 weiteren Autor:innen. Beteiligte Einrichtung: University of Queensland, School of Veterinary Science, Gatton, Queensland, Australia. Hauptthemen laut MEDLINE: Bone Plates, Cervical Vertebrae, Spinal Fusion. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 16 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

To compare the biomechanical properties of a three‐dimensional (3D) printed titanium plate and spacer (3DM) and a 4.5 mm broad locking compression plate (LCP) for intervertebral fusion of C4–C5 in the horse. Study design Ex vivo experimental study. Animals Twenty‐four equine cadaveric cervical spines.

Methods

Twenty‐four cadaver equine cervical spines were randomly assigned to ventral intervertebral fusion with either 3DM ( n = 12) or LCP ( n = 12) at C4–C5. Four‐point bending tests were performed in flexion (3DM n = 6, LCP n = 6) and extension (3DM n = 6, LCP n = 6) in a single cycle to failure. Yield, failure moment, and stiffness in flexion and extension were compared between the 3DM and LCP groups using a mixed effects linear regression model. Failure mode was compared using penalized logistic regression. The significance level was p ≤ .05.

Results

Yield, failure moment, and stiffness were similar between LCP and 3DM groups, with no differences in either flexion or extension. In extension, displaced fractures ( p = .03) and screw pullout ( p = .09) were more common in the LCP group.

Conclusion

The 3DM group had similar yield, failure moment, and stiffness to the LCP group. The LCP constructs were more likely to fail by screw pullout or displaced vertebral fracture in extension. Sample size was a major limitation, so smaller differences in the mechanical variables and failure mode would not have been detected. Clinical significance In a cadaver model, the 3DM construct was less likely to fail by displaced fracture when loaded in extension. This warrants in vivo investigation.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Bone PlatesCervical VertebraeSpinal FusionAnimalsHorsesTitaniumBiomechanical PhenomenaPrinting, Three-DimensionalCadaver

Substanzen

Titanium

Autor:innen und Institutionen

  • University of Queensland, School of Veterinary Science, Gatton, Queensland, Australia.
  • Department of Clinical Studies-New Bolton Center, School of Veterinary Medicine, University of Pennsylvania, Kennett Square, Pennsylvania, USA.
  • Clinique Equine de Grosbois, Boissy Saint Léger, France.

Zitieren

APA

Zedler, S., Jukic, C., van Eps, A., Stefanovski, D., Genton, M., & Rossignol, F. (2025). Ex vivo biomechanical testing of a three‐dimensional printed titanium plate and spacer construct and 4.5 mm locking compression plate for ventral cervical fusion of C4 – C5 in the horse. Veterinary Surgery. https://doi.org/10.1111/vsu.70014

Vancouver

Zedler S, Jukic C, van Eps A, Stefanovski D, Genton M, Rossignol F. Ex vivo biomechanical testing of a three‐dimensional printed titanium plate and spacer construct and 4.5 mm locking compression plate for ventral cervical fusion of C4 – C5 in the horse. Veterinary Surgery. 2025. doi:10.1111/vsu.70014

BibTeX
@article{Zedler2025,
  author = {Zedler, Steven and Jukic, Chantelle and van Eps, Andrew and Stefanovski, Darko and Genton, Martin and Rossignol, Fabrice},
  title = {Ex vivo biomechanical testing of a three‐dimensional printed titanium plate and spacer construct and 4.5 mm locking compression plate for ventral cervical fusion of C4 – C5 in the horse},
  journal = {Veterinary Surgery},
  year = {2025},
  doi = {10.1111/vsu.70014}
}
Kostenlos starten →