EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

A New Technique for Placing Pedicle Screws Into Bone Cement‐Strengthened Vertebrae Involving Drilling and Melting

Yutian Luo, Chaoxin Wang, Kaifeng Ye, Caimei Wang, Xiaolin Ma, Yun Tian iD

Orthopaedic Surgery · 2026

DOI: 10.1111/os.70230 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Orthopaedic Surgery, 2026. Verfasst von Yutian Luo und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Orthopedics, Peking University Third Hospital, Beijing, China. Hauptthemen laut MEDLINE: Bone Cements, Pedicle Screws, Spine, Vertebroplasty. Die Arbeit nennt 24 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

Vertebroplasty with non‐degradable polymethyl methacrylate bone cement is a common procedure in spine surgery. However, this bone cement reinforcement of the vertebral body could affect subsequent spinal surgeries, especially for pedicle screw insertion. This study proposes a novel method of inserting pedicle screws into bone cement‐reinforced vertebral bodies through thermal softening via Kirschner wires (K‐wires) drilling, and conducts preliminary in vitro experiments to assess its feasibility and safety.

Methods

This study includes bone cement block experiments and in vitro goat bone experiments. The bone cement block experiment utilized a CNC machine to drill into bone cement blocks with varying K‐wire diameters, rotational speeds, and feed rates, followed by the insertion of pedicle screws. The highest temperature during the procedure and the pull‐out strength of the pedicle screws were recorded for different groups. A two‐way ANOVA was used for comparative analysis. The goat bone experiment consisted of an experimental group and a control group. The control group had screws inserted along the pedicle after drilling. In the experimental group, screws were inserted after softening the old bone cement within the vertebral body using a 3.5 mm K‐wire for drilling. The highest temperature during the procedure was recorded for the experimental group, and pull‐out tests were conducted on the screws of both groups after the procedure. The pull‐out results from the goat bone experiment were analyzed using Student's t ‐test.

Results

Bone cement block experiment: Drilling with K‐wires caused a significant temperature increase in the bone cement blocks, with temperature rises at 4 mm ranging from 28.1°C to 75.9°C. The maximum pull‐out loads across all groups ranged from 2455.053 to 15201.94 N. In the goat bone experiment, the experimental group showed temperature increases of 8.38°C ± 3.07°C beneath the pedicle, 11.18°C ± 1.42°C in the spinal canal, and 8.26°C ± 3.46°C anterior to the vertebral body during drilling. The average maximum loads for the experimental and control groups were 910.5504 ± 221.6544 N and 294.229 ± 40.3475 N, respectively, indicating a statistically significant difference between the two groups ( p = 0.0001).

Conclusion

The experimental results demonstrate that screws can be inserted into bone cement after thermal softening via K‐wire drilling, achieving good pull‐out resistance. In the goat bone experiment, the average temperature increase around the vertebral body was measured to be below 10°C, indicating a low risk of thermal damage to the surrounding tissues.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Bone CementsPedicle ScrewsSpineVertebroplastyAnimalsGoatsFeasibility StudiesBone WiresFreezingHot TemperatureModels, AnimalPolymethyl Methacrylate

Stichwörter der Autor:innen

bone cementosteoporosispolymethyl methacrylatevertebral augmentation

Substanzen

Bone CementsPolymethyl Methacrylate

Autor:innen und Institutionen

  • Department of Orthopedics, Peking University Third Hospital, Beijing, China.
  • Department of Orthopaedic Surgery, the First Affiliated Hospital, Fujian Medical University, Fuzhou, China.
  • Beijing AKEC Medical Co. Ltd., Beijing, China.

ORCID-Profile: Yun Tian

Zitieren

APA

Luo, Y., Wang, C., Ye, K., Wang, C., Ma, X., & Tian, Y. (2026). A New Technique for Placing Pedicle Screws Into Bone Cement‐Strengthened Vertebrae Involving Drilling and Melting. Orthopaedic Surgery. https://doi.org/10.1111/os.70230

Vancouver

Luo Y, Wang C, Ye K, Wang C, Ma X, Tian Y. A New Technique for Placing Pedicle Screws Into Bone Cement‐Strengthened Vertebrae Involving Drilling and Melting. Orthopaedic Surgery. 2026. doi:10.1111/os.70230

BibTeX
@article{Luo2026,
  author = {Luo, Yutian and Wang, Chaoxin and Ye, Kaifeng and Wang, Caimei and Ma, Xiaolin and Tian, Yun},
  title = {A New Technique for Placing Pedicle Screws Into Bone Cement‐Strengthened Vertebrae Involving Drilling and Melting},
  journal = {Orthopaedic Surgery},
  year = {2026},
  doi = {10.1111/os.70230}
}
Kostenlos starten →