EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Clinical Application of 3D ‐Printed Custom Hemipelvic Prostheses With Re‐Entrant Chiral Structure in Reconstruction After Pelvic Tumor Resection

Linyun Tan iD, Ye Li, Xin Hu, Yitian Wang, Xiaolu Zhang, Xiaoyan Liu iD, Yi Luo, Yong Zhou, Chongqi Tu, Xiao Yang iD, Li Min

Orthopaedic Surgery · 2025-11 · 17 (11) · 3067-3077

DOI: 10.1111/os.70159 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Orthopaedic Surgery, online erschienen am 21.08.2025. Verfasst von Linyun Tan und 10 weiteren Autor:innen. Beteiligte Einrichtung: Department of Orthopedic Surgery and Orthopedic Research Institute, West China Hospital, Sichuan University, Chengdu, Sichuan, China. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Prosthesis Design, Plastic Surgery Procedures, Bone Neoplasms. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Sichuan Province Science and Technology Support Program, Sichuan Science and Technology Agency, National Key Research and Development Program of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

Pelvic reconstruction with conventional 3D‐printed prostheses faces a critical trade‐off, where achieving sufficient porosity for optimal bone ingrowth often compromises essential mechanical stability. To address this challenge, this study evaluates the clinical outcomes of 3D‐printed hemipelvic prostheses incorporating re‐entrant chiral structure (RCS), a novel negative Poisson's ratio design, in patients undergoing pelvic reconstruction following tumor resection.

Methods

A retrospective analysis was conducted on 15 patients (eight females and seven males; mean age: 39.3 ± 11.7 years) with pelvic malignancies who underwent reconstruction using 3D‐printed hemipelvic prostheses incorporating RCS between March 2018 and June 2023. The diagnoses included osteosarcoma ( n = 8), Ewing's sarcoma ( n = 3), chondrosarcoma ( n = 2), and high‐grade soft tissue sarcoma ( n = 2). All patients were staged as IIB according to the Enneking system, except for one case of Ewing's sarcoma (stage III). Neoadjuvant chemotherapy (four cycles) was administered to six osteosarcoma patients, and one Ewing's sarcoma patient received six cycles, while other patients proceeded directly to surgery. Patient outcomes were systematically evaluated through oncological status, functional performance (MSTS‐93 score), pain assessment (VAS score), surgical parameters, complications, and radiographic analysis using Tomosynthesis Shimadzu Metal Artifact Reduction Technology (T‐SMART).

Results

At the latest follow‐up (44.5 ± 9.4 months), 13 patients (86.7%) remained disease‐free; one patient (6.7%) experienced local recurrence requiring revision surgery, and one patient (6.7%) died of metastatic complications at 32 months post‐surgery. Functional outcomes showed significant improvement, with mean MSTS‐93 scores increasing from 14.5 ± 1.1 preoperatively to 25.8 ± 1.3 at final follow‐up ( p < 0.001). Pain control was satisfactory, with VAS scores decreasing from 5.5 ± 0.6 to 1.5 ± 0.5 ( p < 0.001). The mean surgical duration was 289.3 ± 30.4 min, with an average intraoperative blood loss of 3540 ± 621.5 mL. Early complications included delayed wound healing in three cases (20%), successfully managed with wound care protocols and VAC therapy. One patient (6.7%) developed deep prosthetic infection at 14 months post‐surgery, necessitating a two‐stage revision procedure. No mechanical failures, aseptic loosening, or prosthesis fractures were observed during the follow‐up period. Radiographic analysis demonstrated progressive bone ingrowth into the RCS porous regions in all cases, with no signs of osteolysis or implant migration in the remaining prostheses.

Conclusion

D‐printed custom hemipelvic prostheses with RCS offer an effective solution for pelvic reconstruction by achieving an optimal balance between mechanical stability and biological integration, leading to promising clinical outcomes.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalProsthesis DesignPlastic Surgery ProceduresBone NeoplasmsPelvic BonesPelvic NeoplasmsProstheses and ImplantsHumansFemaleMaleRetrospective StudiesAdultMiddle Aged

Stichwörter der Autor:innen

3D‐printed prosthesisearly clinical outcomesnegative Poisson's ratiopelvic reconstructionre‐entrant chiral structure

Autor:innen und Institutionen

  • Department of Orthopedic Surgery and Orthopedic Research Institute, West China Hospital, Sichuan University, Chengdu, Sichuan, China.
  • Model Worker and Craftsman Talent Innovation Workshop of Sichuan Province, Chengdu, Sichuan, China.
  • Department of Orthopedics Surgery, West China Hospital, Sichuan University/West China School of Nursing, Chengdu, Sichuan, China.
  • National Engineering Research Center for Biomaterials, Sichuan University, Chengdu, China.
  • Provincial Engineering Research Center for Biomaterials Genome of Sichuan, Sichuan University, Chengdu, China.

ORCID-Profile: Linyun Tan, Xiaoyan Liu, Xiao Yang

Förderung

  • Sichuan Province Science and Technology Support Program
  • Sichuan Science and Technology Agency
  • National Key Research and Development Program of China
  • Noncommunicable Chronic Diseases-National Science and Technology Major Project
  • Sichuan Provincial Science and Technology Support Program

Zitieren

APA

Tan, L., Li, Y., Hu, X., Wang, Y., Zhang, X., Liu, X., Luo, Y., Zhou, Y., Tu, C., Yang, X., & Min, L. (2025). Clinical Application of 3D ‐Printed Custom Hemipelvic Prostheses With Re‐Entrant Chiral Structure in Reconstruction After Pelvic Tumor Resection. Orthopaedic Surgery, 17(11), 3067-3077. https://doi.org/10.1111/os.70159

Vancouver

Tan L, Li Y, Hu X, Wang Y, Zhang X, Liu X, et al. Clinical Application of 3D ‐Printed Custom Hemipelvic Prostheses With Re‐Entrant Chiral Structure in Reconstruction After Pelvic Tumor Resection. Orthopaedic Surgery. 2025;17(11):3067-3077. doi:10.1111/os.70159

BibTeX
@article{Tan2025,
  author = {Tan, Linyun and Li, Ye and Hu, Xin and Wang, Yitian and Zhang, Xiaolu and Liu, Xiaoyan and Luo, Yi and Zhou, Yong and Tu, Chongqi and Yang, Xiao and Min, Li},
  title = {Clinical Application of 3D ‐Printed Custom Hemipelvic Prostheses With Re‐Entrant Chiral Structure in Reconstruction After Pelvic Tumor Resection},
  journal = {Orthopaedic Surgery},
  year = {2025},
  volume = {17},
  number = {11},
  pages = {3067--3077},
  doi = {10.1111/os.70159}
}
Kostenlos starten →