EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D assessment of the marginal and internal gap and fracture load of ceramic surveyed inlays designed for removable partial denture support: An in vitro comparative study

Mohammed M Gad iD, Amr A Mahrous iD, Shorooq K Almajhad iD, Amjaad M Almarzoogi, Majd A Alotaibi iD, Haidar Alalawi iD, Ahmad M Al-Thobity iD, Passent Ellakany iD, Shaimaa M Fouda iD, Moamen A Abdalla iD, Nadim Z Baba iD, Fahad A Al-Harbi iD

Journal of Prosthodontics · 18.08.2026

DOI: 10.1111/jopr.70223 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 18.08.2026. Verfasst von Mohammed M Gad und 11 weiteren Autor:innen. Beteiligte Einrichtung: Department of Substitutive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia. Die Arbeit nennt 55 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To assess the internal and marginal gaps and the fracture load of different machinable ceramics for an inlay acting as a support for a removable partial denture. Materials and Methods Sixty extracted human teeth (first maxillary premolar) were collected ( n = 10 for each group). Intact teeth served as the negative control group, and there were six experimental groups: direct composite resin group (positive control); IPS Empress Direct composite (EDC); Feldspathic ceramic, VITABLOCS Mark II (FLD); Leucite glass‐ceramic IPS Empress CAD (LGC); zirconia‐reinforced lithium silicate Celtra Duo (ZLS); and zirconium oxide IPS E.max ZirCAD (ZRC). Disto‐occlusal inlay cavities were prepared in the assigned teeth. For ceramic groups, teeth were scanned using a Trios III intraoral scanner (IOS). Inlays were virtually designed to incorporate a rest seat and then milled. The three‐dimensional (3D) internal and marginal gaps were assessed with a replica technique combined with a second scan of the fit checker applied before inlay cementation. 3D inspection software was used for the superimposition of scans and the calculation of the internal and marginal gaps. Inlay restorations were cemented using a dual‐polymerizing resin cement, then subjected to thermocycling and cyclic loading, followed by load till failure. The internal and marginal gap and fracture load values were recorded and statistically analyzed using One‐way ANOVA with post hoc Tukey test for comparisons ( α = 0.05). Failure patterns were analyzed.

Results

The least significant marginal gap was seen with the ZRC group (68 ± 7 µm), while the ZLS group presented the highest marginal and internal gap values (135 ± 9, 199 ± 61 µm), respectively. Internal gap comparison revealed non‐significant differences among the FLD, LGC, and ZRC groups. ZRC group demonstrated significantly the highest fracture load value (1830 ± 97 N). On the contrary, composite resin and FLD groups showed the lowest fracture load in comparison to the tested groups ( p < 0.001). Failure pattern with the ZRC group revealed predominance of tooth failure, as well as adhesive failure associated with debonding of the restoration. LGC and ZLS groups revealed common performance with prevalence of tooth and restoration failure of mixed type, while both direct composite restoration and FLD groups showed predominately cohesive restoration failures.

Conclusion

Indirect machinable ceramic surveyed inlays revealed acceptable gap values in addition to outstanding fracture load when compared to direct composite inlays.

Schlagwörter

Stichwörter der Autor:innen

composite resinfracture loadinlaymachinable ceramicmisfitremovable partial denture

Autor:innen und Institutionen

  • Department of Substitutive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • Division of Prosthodontics, School of Dentistry, University of Alabama at Birmingham, Birmingham, Alabama, USA.
  • Advanced Specialty Education Program in Implant Dentistry, Loma Linda University, School of Dentistry, Loma Linda, California, USA.

ORCID-Profile: Mohammed M Gad, Amr A Mahrous, Shorooq K Almajhad, Majd A Alotaibi, Haidar Alalawi, Ahmad M Al-Thobity, Passent Ellakany, Shaimaa M Fouda, Moamen A Abdalla, Nadim Z Baba, Fahad A Al-Harbi

Zitieren

APA

Gad, M. M., Mahrous, A. A., Almajhad, S. K., Almarzoogi, A. M., Alotaibi, M. A., Alalawi, H., Al-Thobity, A. M., Ellakany, P., Fouda, S. M., Abdalla, M. A., Baba, N. Z., & Al-Harbi, F. A. (2026). 3D assessment of the marginal and internal gap and fracture load of ceramic surveyed inlays designed for removable partial denture support: An in vitro comparative study. Journal of Prosthodontics. https://doi.org/10.1111/jopr.70223

Vancouver

Gad MM, Mahrous AA, Almajhad SK, Almarzoogi AM, Alotaibi MA, Alalawi H, et al. 3D assessment of the marginal and internal gap and fracture load of ceramic surveyed inlays designed for removable partial denture support: An in vitro comparative study. Journal of Prosthodontics. 2026. doi:10.1111/jopr.70223

BibTeX
@article{Gad2026,
  author = {Gad, Mohammed M and Mahrous, Amr A and Almajhad, Shorooq K and Almarzoogi, Amjaad M and Alotaibi, Majd A and Alalawi, Haidar and Al-Thobity, Ahmad M and Ellakany, Passent and Fouda, Shaimaa M and Abdalla, Moamen A and Baba, Nadim Z and Al-Harbi, Fahad A},
  title = {3D assessment of the marginal and internal gap and fracture load of ceramic surveyed inlays designed for removable partial denture support: An in vitro comparative study},
  journal = {Journal of Prosthodontics},
  year = {2026},
  doi = {10.1111/jopr.70223}
}
Kostenlos starten →