EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of resin type, cleaning solution, and aging on the mechanical properties and reliability of additively manufactured occlusal devices

Selim Polat, Ayyüce Nur Tezcan, Hanan Al-Johani iD, Gülce Çakmak iD, Mustafa Borga Dönmez iD, Burak Yilmaz iD

Journal of Prosthodontics · 13.03.2026

DOI: 10.1111/jopr.70121 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 13.03.2026. Verfasst von Selim Polat und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The purpose of this in vitro study was to investigate the effect of alcohol‐free cleaning solutions on the mechanical properties and reliability of additively manufactured occlusal device resins, compared with isopropyl alcohol (IPA), while considering the influence of aging. Materials and Methods Bar‐shaped (64×10×3.3 mm) specimens were additively manufactured from two occlusal device resins (Freeprint Splint 2.0; FS, KeySplint Hard; KS) and divided into three groups based on the cleaning solution used (IPA, methylether solvent (MES), and a water‐based solution) ( N = 30). After postprocessing, each set of specimens was further divided into two groups based on their aging condition as nonaged or aged ( n = 15). Specimens in nonaged subgroups were tested for 3‐point flexural strength and microhardness, while those in aged subgroups were subjected to 5000 thermal cycles between 5°C and 55°C before testing. Both data sets were analyzed with a generalized linear model either with a normal distribution and identity link function (microhardness) or a gamma distribution and logarithmic link function (flexural strength). The maximum likelihood estimation method was used for the Weibull analysis of the flexural strength data and further evaluated with the chi‐squared test ( α = 0.05).

Results

Aged KS had higher flexural strength than its FS counterpart when IPA and MES were used ( P ≤ 0.014). MES led to the lowest flexural strength for aged FS, which had lower values than nonaged FS when MES and the water‐based solution were used ( p ≤ 0.002). Nonaged MES‐cleaned KS had lower hardness than its FS counterpart ( p

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingagingcleaning solutionflexural strengthocclusal device resins

Autor:innen und Institutionen

  • Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland.
  • Department of Prosthodontics, Faculty of Dentistry, Necmettin Erbakan University, Konya, Turkey.
  • Department of Restorative Dentistry, Faculty of Dentistry, King Abdulaziz University, Jeddah, Saudi Arabia.
  • Digital Dental Technology Laboratory, Department of Prosthodontics, Geriatric Dentistry and Craniomandibular Disorders, Charité Universitätsmedizin Berlin, Corporate Member of Freie Universität Berlin and Humboldt-Unive…
  • Department of Prosthodontics, Faculty of Dentistry, Biruni University, Istanbul, Turkey.
  • Department of Restorative, Preventive and Pediatric Dentistry, School of Dental Medicine, University of Bern, Bern, Switzerland.

ORCID-Profile: Hanan Al-Johani, Gülce Çakmak, Mustafa Borga Dönmez, Burak Yilmaz

Zitieren

APA

Polat, S., Tezcan, A. N., Al-Johani, H., Çakmak, G., Dönmez, M. B., & Yilmaz, B. (2026). Effect of resin type, cleaning solution, and aging on the mechanical properties and reliability of additively manufactured occlusal devices. Journal of Prosthodontics. https://doi.org/10.1111/jopr.70121

Vancouver

Polat S, Tezcan AN, Al-Johani H, Çakmak G, Dönmez MB, Yilmaz B. Effect of resin type, cleaning solution, and aging on the mechanical properties and reliability of additively manufactured occlusal devices. Journal of Prosthodontics. 2026. doi:10.1111/jopr.70121

BibTeX
@article{Polat2026,
  author = {Polat, Selim and Tezcan, Ayyüce Nur and Al-Johani, Hanan and Çakmak, Gülce and Dönmez, Mustafa Borga and Yilmaz, Burak},
  title = {Effect of resin type, cleaning solution, and aging on the mechanical properties and reliability of additively manufactured occlusal devices},
  journal = {Journal of Prosthodontics},
  year = {2026},
  doi = {10.1111/jopr.70121}
}
Kostenlos starten →