EUVIMEDEUVIMED entdecken
Crossref

Influence of material and technique of conversion on interim prosthesis fracture

John Bender, Jack Piermatti, Daniel Feit, Tanpreet Minhas

Journal of Prosthodontics · 2025

DOI: 10.1111/jopr.70020 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, 2025. Verfasst von John Bender und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Nova Southeastern University College of Dental Medicine, Fort Lauderdale, Florida, USA. Hauptthemen laut MEDLINE: Dental Restoration Failure, Dental Materials, Dental Prosthesis, Implant-Supported, Denture Design. Die Arbeit nennt 11 Literaturangaben. Gefördert von: Nova Southeastern University HPD.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To investigate the ability of the smart denture conversion (SDC) technique to produce a stronger interim full‐arch implant restoration. Materials and Methods Three materials (OnX Tough 3D‐printed resin, milled PMMA, and injection molded PMMA) were used to fabricate 180 specimens, 60 specimens per material. Then, an equal number of specimens were assigned a conversion technique: either traditional denture conversion or smart denture conversion. The conversions were performed on a pickup jig containing two multiunit abutment replicas. Acrylic resin was used as the pickup material. After denture conversions were performed, all specimens had uniform dimensions. To evaluate mechanical strength, each specimen underwent a 3‐point bend test using an Instron machine with static load testing. Data analysis employed a two‐way ANOVA considering material type, method of conversion, and their interaction, with Tukey HSD post hoc tests conducted in STATA 18.0, where significance was set at p < 0.05.

Results

Results from this study are described as method of conversion, material, and the combination of method of conversion and material. The method of conversion was statistically significant for mean fracture strength, resulting in a p ‐value < 0.037. Choice of material showed statistically significant results for mean fracture strength, with a p ‐value < 0.000. The combination of method of conversion and material showed a statistically significant result for mean fracture strength with a p ‐value < 0.000.

Conclusion

Out of 180 specimens, the combination of OnX Tough 3D‐printed specimens converted with smart denture conversion yielded the highest mean fracture strength and the highest individual fracture strength value.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental Restoration FailureDental MaterialsDental Prosthesis, Implant-SupportedDenture DesignDental Restoration, TemporaryHumansPolymethyl MethacrylateDental Stress AnalysisMaterials TestingAcrylic ResinsPrinting, Three-Dimensional

Stichwörter der Autor:innen

3D‐printed resinPMMA acrylic resin materialdental implantfracture strengthinjection molded PMMAsmart denture conversion techniquetraditional denture conversion technique

Substanzen

Polymethyl MethacrylateDental MaterialsAcrylic Resins

Autor:innen und Institutionen

  • Department of Prosthodontics, Nova Southeastern University College of Dental Medicine, Fort Lauderdale, Florida, USA.
  • Rutgers, The State University of New Jersey, Newark, New Jersey, USA.

Förderung

  • Nova Southeastern University HPD

Zitieren

APA

Bender, J., Piermatti, J., Feit, D., & Minhas, T. (2025). Influence of material and technique of conversion on interim prosthesis fracture. Journal of Prosthodontics. https://doi.org/10.1111/jopr.70020

Vancouver

Bender J, Piermatti J, Feit D, Minhas T. Influence of material and technique of conversion on interim prosthesis fracture. Journal of Prosthodontics. 2025. doi:10.1111/jopr.70020

BibTeX
@article{Bender2025,
  author = {Bender, John and Piermatti, Jack and Feit, Daniel and Minhas, Tanpreet},
  title = {Influence of material and technique of conversion on interim prosthesis fracture},
  journal = {Journal of Prosthodontics},
  year = {2025},
  doi = {10.1111/jopr.70020}
}
Kostenlos starten →