EUVIMEDEUVIMED entdecken
Crossref

The impact of customized surface topography and porosity created by additive manufacturing technology on gingival fibroblasts

Saumya Khurana, Franciele Floriani iD, Yingzi Li, Xiaohua Liu, Amirali Zandinejad

Journal of Prosthodontics · 2025

DOI: 10.1111/jopr.14030 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, 2025. Verfasst von Saumya Khurana und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Biomedical Science, College of Dentistry, Texas A&M University, Dallas, Texas, USA. Hauptthemen laut MEDLINE: Fibroblasts, Gingiva, Polymethyl Methacrylate, Printing, Three-Dimensional. Die Arbeit nennt 41 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The purpose of this study was to analyze gingival fibroblast proliferation on additively manufactured polymethylmethacrylate (PMMA) groups with different surface characteristics namely no treatment group (NTG) and customized 250 µm diameter porosity (AM‐250G) group. Materials and Methods 3D‐printed NTG was compared for its influence on growth of cells to a additively manufactured surface with porosity (AM‐250G). For each group (NTG, AM‐250G) 20 samples of material were tested. Fibroblast cells, at a concentration of 2.5 × 10 4 cells/mL, were seeded into 48 plates separately into two groups (NTG, AM‐250G). These were cultured in Dulbecco's Modified Eagle's Medium (DMEM) supplemented with 10% fetal bovine serum (FBS) at 37°C and 5% CO2 atmosphere. For cell proliferation MTT assay was conducted at 24, 48, and 72 h. Cell proliferation was quantified through optical density (OD) measurements of the cell supernatant, and surface analysis was conducted using a scanning electron microscope (SEM). Data normality was confirmed by the Shapiro–Wilk test, with a significance level set at p < 0.05. Statistical analysis was conducted using an independent Student's t ‐test at each time point.

Results

A significant difference in cell proliferation was observed at 24 h, with the NTG group showing higher cell numbers compared to AM‐250G group. Qualitative analysis of cell culture was performed using scanning electron microscopy to compare to the NTG and the porosity (AM‐250G) groups after 24, 48, and 72 h of fibroblast tissue attachment. No significant differences were observed between the groups at the 48 and 72‐h intervals.

Conclusions

At 24 h, the NTG surface demonstrated superior cell proliferation compared to the surface with porosity (AM‐250G). However, significant differences in cell growth on both materials at 48 and 72 h, suggesting that both surface types eventually support similar levels of cell proliferation, with an increase of extensive spread and elongation of fibroblasts cells proliferation on the surface with porosity.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

FibroblastsGingivaPolymethyl MethacrylatePrinting, Three-DimensionalPorosityCell ProliferationSurface PropertiesHumansCells, CulturedMicroscopy, Electron, Scanning

Stichwörter der Autor:innen

additive manufacturinggingival fibroblastssurface porosity

Substanzen

Polymethyl Methacrylate

Autor:innen und Institutionen

  • Department of Biomedical Science, College of Dentistry, Texas A&M University, Dallas, Texas, USA.
  • Department of Prosthodontics, University of Iowa, Iowa City, Iowa, USA.
  • Department of Chemical and Biomedical Engineering, University of Missouri, Columbia, Missouri, USA.
  • Prosthodontist, Implant Dentistry Associates of Arlington, Arlington, Texas, USA.

ORCID-Profile: Franciele Floriani

Zitieren

APA

Khurana, S., Floriani, F., Li, Y., Liu, X., & Zandinejad, A. (2025). The impact of customized surface topography and porosity created by additive manufacturing technology on gingival fibroblasts. Journal of Prosthodontics. https://doi.org/10.1111/jopr.14030

Vancouver

Khurana S, Floriani F, Li Y, Liu X, Zandinejad A. The impact of customized surface topography and porosity created by additive manufacturing technology on gingival fibroblasts. Journal of Prosthodontics. 2025. doi:10.1111/jopr.14030

BibTeX
@article{Khurana2025,
  author = {Khurana, Saumya and Floriani, Franciele and Li, Yingzi and Liu, Xiaohua and Zandinejad, Amirali},
  title = {The impact of customized surface topography and porosity created by additive manufacturing technology on gingival fibroblasts},
  journal = {Journal of Prosthodontics},
  year = {2025},
  doi = {10.1111/jopr.14030}
}
Kostenlos starten →