EUVIMEDEUVIMED entdecken
Open Access

Effect of different surface treatments and adhesive cementation on the surface topography and flexural strength of translucent and ultra‐translucent monolithic zirconia

Bianca Cristina Dantas da Silva, Sarah Emille Gomes da Silva, Nathália Ramos da Silva, Fernanda Gurgel Gois de Moreira, Karina Barbosa Souza, Yu Zhang, Rodrigo Othávio Assunção de Souza iD

Journal of Prosthodontics · 2024

DOI: 10.1111/jopr.13929 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, 2024. Verfasst von Bianca Cristina Dantas da Silva und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Dentistry, Federal University of Rio Grande do Norte (UFRN), Natal, Rio Grande do Norte, Brazil. Hauptthemen laut MEDLINE: Zirconium, Flexural Strength, Cementation, Dental Materials. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar. Gefördert von: NIDCR NIH HHS, US National Institutes of Health, Coordination for the Improvement of Higher Education Personnel-Brazil.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To evaluate the effect of different surface treatments and adhesive cementation on the miniflexural strength (MFS) of monolithic zirconia. Materials and Methods Two‐hundred and forty (240) sintered bars of translucent zirconia (Z T ) and ultra‐translucent zirconia (Z UT ) were obtained (8 mm ×2 mm ×1 mm). The bars were divided into 16 groups ( n = 15) according to the factors “Zirconia” (Z T and Z UT ), “Cementation” (Cem) and “surface treatment” (Ctrl:Control, Al:Aluminum oxide/Al 2 O 3 50 µm, Si:Silica/SiO 2 coated alumina particles oxide 30 µm, Gl:Glazing+hydrofluoric acid). Half of the bars received an adhesive layer application, followed by application of resin cement and light curing. The surface roughness was measured in non‐cemented groups. All the bars were subjected to the MFS test (1.0 mm/min; 100 kgf). Scanning electron microscopy was used for qualitative analyses. MFS data (MPa) and roughness (µm) were statistically evaluated by three‐way and two‐way ANOVA respectively and Tukey's test (5%).

Results

The surface treatment and the interaction were significant for roughness. Glazing promoted less roughness compared to silicatization. Regarding MFS, only the zirconia and surface treatment factors were significant. For Z T , the sandblasted groups had an increase in MFS and glazing reduced it. There was no difference between the groups without cementation for the Z UT ; however, Z UT .Si/Cem, and Z UT .Al/Cem obtained superior MFS among the cemented groups.

Conclusions

Sandblasting increases the flexural strength for Z T , while glaze application tends to reduce it. Applying resin cement increases the flexural strength of Z UT when associated with sandblasting. Sandblasting protocols promote greater surface roughness.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ZirconiumFlexural StrengthCementationDental MaterialsSurface PropertiesMaterials TestingResin CementsMicroscopy, Electron, ScanningDental Stress Analysis

Stichwörter der Autor:innen

flexural strengthresin cementsandblastingsurface treatmentzirconia

Substanzen

Zirconiumzirconium oxideResin CementsDental Materials

Autor:innen und Institutionen

  • Department of Dentistry, Federal University of Rio Grande do Norte (UFRN), Natal, Rio Grande do Norte, Brazil.
  • Institute of Science and Technology, Paulista State University (UNESP), São José dos Campos, São Paulo, Brazil.
  • Department of Preventive and Restorative, University of Pennsylvania, School of Dental Medicine, Philadelphia, USA.
  • Department of Dentistry, Adjunct Professor in Prosthodontics, Federal University of Rio Grande do Norte (UFRN), Natal, Rio Grande do Norte, Brazil.

ORCID-Profile: Rodrigo Othávio Assunção de Souza

Förderung

  • NIDCR NIH HHS
  • US National Institutes of Health
  • Coordination for the Improvement of Higher Education Personnel-Brazil
  • National Institute of Dental and Craniofacial Research

Zitieren

APA

da Silva, B. C. D., da Silva, S. E. G., da Silva, N. R., de Moreira, F. G. G., Souza, K. B., Zhang, Y., & de Souza, R. O. A. (2024). Effect of different surface treatments and adhesive cementation on the surface topography and flexural strength of translucent and ultra‐translucent monolithic zirconia. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13929

Vancouver

da Silva BCD, da Silva SEG, da Silva NR, de Moreira FGG, Souza KB, Zhang Y, et al. Effect of different surface treatments and adhesive cementation on the surface topography and flexural strength of translucent and ultra‐translucent monolithic zirconia. Journal of Prosthodontics. 2024. doi:10.1111/jopr.13929

BibTeX
@article{daSilva2024,
  author = {da Silva, Bianca Cristina Dantas and da Silva, Sarah Emille Gomes and da Silva, Nathália Ramos and de Moreira, Fernanda Gurgel Gois and Souza, Karina Barbosa and Zhang, Yu and de Souza, Rodrigo Othávio Assunção},
  title = {Effect of different surface treatments and adhesive cementation on the surface topography and flexural strength of translucent and ultra‐translucent monolithic zirconia},
  journal = {Journal of Prosthodontics},
  year = {2024},
  doi = {10.1111/jopr.13929}
}
Kostenlos starten →