EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

In vitro analysis of monomer leaching in modern dental materials: CAD milled, printed, traditional heat‐processed, and auto‐polymerizing denture base resins

Greta Smidt iD, Shang Gao, Divya Iyer, Samanvaya Srivastava, Kumar C Shah

Journal of Prosthodontics · 2025-12 · 34 (9) · 988-992

DOI: 10.1111/jopr.13874 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 10.06.2024. Verfasst von Greta Smidt und 4 weiteren Autor:innen. Beteiligte Einrichtung: Advanced Graduate Prosthodontics Department, University of California School of Dentistry, Los Angeles, California, USA. Hauptthemen laut MEDLINE: Polymethyl Methacrylate, Denture Bases, Dental Materials, Computer-Aided Design. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 11 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

Denture fabrication has shifted from traditional heat‐processed and auto‐polymerizing materials to computer‐aided design and computer‐aided manufacturing (CAD‐CAM) milled and printed materials. The monomer in traditional materials can induce an allergic reaction in some patients. With the rise in the edentulous population and increasing demand for the fabrication of dentures, these newer materials should be studied for monomer leaching. The purpose of this study was to evaluate the ratio of residual monomer in materials being used for denture bases: CAD‐milled polymethylmethacrylate (PMMA), printed denture base resin, heat‐processed PMMA, and auto‐polymerizing PMMA comparatively. Materials and Methods Milled, printed, heat‐activated, and auto‐polymerizing denture base specimens ( n = 3 for each group, each test run three times) were fabricated according to manufacturer recommendations. Specimens were first immersed in deuterated chloroform (CDCl 3 ), a deuterated organic solvent, to evaluate monomer leaching and to observe physical properties of the materials. NMR spectroscopy was used to evaluate the dissolution of materials and residual monomer to crosslinked polymer ratios at 1, 4, and 9 days. A second group of specimens was then immersed in deuterium oxide (D 2 O) to evaluate if the residual monomers would leach out of the system. The solution was then analyzed using nuclear magnetic resonance (NMR) spectroscopy for 1 month. The deuterated forms of chloroform (CDCl 3 ) and water (D 2 O) were used to enable sample characterization by NMR.

Results

While the heat‐processed, auto‐polymerizing, and milled specimens possessed residual monomers, no significant monomer leaching was noted in the printed specimen, while immersed in CDCl 3 . Similarly, the printed specimen was most resistant to dissolution, as compared to the rest; dissolution of the specimen is indicative of little to no cross‐linking. No detectable dissolution of monomer was seen when all specimens were immersed in D 2 O for up to 1 month.

Conclusions

Residual monomers were not found in the printed denture material in this study in either CDCl 3 or D 2 O, whereas CAD‐milled and traditionally processed denture bases still have residual monomers within their respective systems when immersed in organic solvent. None of the specimens tested leached monomers into D 2 O.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Polymethyl MethacrylateDenture BasesDental MaterialsComputer-Aided DesignAcrylic ResinsHot TemperatureMaterials TestingPolymerizationDenture DesignIn Vitro Techniques

Stichwörter der Autor:innen

denture basedenturesmonomerpolymer

Substanzen

Polymethyl MethacrylateDental MaterialsAcrylic Resins

Autor:innen und Institutionen

  • Advanced Graduate Prosthodontics Department, University of California School of Dentistry, Los Angeles, California, USA.
  • Chemical and Biomolecular Engineering Department, University of California, Los Angeles, California, USA.
  • Faculty Group Dental Practice, University of California School of Dentistry, Los Angeles, California, USA.

ORCID-Profile: Greta Smidt

Zitieren

APA

Smidt, G., Gao, S., Iyer, D., Srivastava, S., & Shah, K. C. (2025). In vitro analysis of monomer leaching in modern dental materials: CAD milled, printed, traditional heat‐processed, and auto‐polymerizing denture base resins. Journal of Prosthodontics, 34(9), 988-992. https://doi.org/10.1111/jopr.13874

Vancouver

Smidt G, Gao S, Iyer D, Srivastava S, Shah KC. In vitro analysis of monomer leaching in modern dental materials: CAD milled, printed, traditional heat‐processed, and auto‐polymerizing denture base resins. Journal of Prosthodontics. 2025;34(9):988-992. doi:10.1111/jopr.13874

BibTeX
@article{Smidt2025,
  author = {Smidt, Greta and Gao, Shang and Iyer, Divya and Srivastava, Samanvaya and Shah, Kumar C},
  title = {In vitro analysis of monomer leaching in modern dental materials: CAD milled, printed, traditional heat‐processed, and auto‐polymerizing denture base resins},
  journal = {Journal of Prosthodontics},
  year = {2025},
  volume = {34},
  number = {9},
  pages = {988--992},
  doi = {10.1111/jopr.13874}
}
Kostenlos starten →