EUVIMEDEUVIMED entdecken
Crossref

Influence of different printing orientations and post‐polymerization time on the translucency of three‐dimensional (3D) printed denture base resins

Mohammed M Gad iD, Shaimaa M Fouda iD, Hend Alshammary, Raand Altayyar, Ahmed Elakel iD, Essam A Nassar iD, Soban Q Khan iD, Ahmed M Rahoma iD, Ahmed Fathey Elhagali, Mutlu Özcan iD, Fahad A Al-Harbi iD

Journal of Prosthodontics · 2024

DOI: 10.1111/jopr.13866 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, 2024. Verfasst von Mohammed M Gad und 10 weiteren Autor:innen. Beteiligte Einrichtung: Department of Substitutive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Polymerization, Denture Bases, Acrylic Resins. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 52 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To evaluate the effect of different printing orientations and post‐polymerization time with thermal cycling on the translucency of 3D‐printed denture base resins.

Methods

Heat‐polymerized (HP) acrylic resin specimens were fabricated and 3D‐printed denture base materials (NextDent, ASIGA, FormLabs) were printed with different printing orientations (0, 45, 90 degrees) and subjected to different post‐polymerization times (15‐, 30‐, 60‐, and 90‐min). All specimens were polished and immersed in distilled water for 1 day at 37°C. CIEDE2000 was used to measure the translucency parameters (TP 00 ) before and after thermal cycling (5000 cycles) recording the color parameters (L * , a * , b * ) against a black and white background using a spectrophotometer. k ‐factors ANOVA followed by post hoc Tukey's test (α = .05) was performed for statistical analysis.

Results

The k ‐factors ANOVA test showed a significant effect of resin material, post‐polymerization time, and printing orientation on translucency ( p < 0.001). In comparison to HP, all 3D‐printed resins showed lower translucency with all post‐polymerization times and printing orientation ( p < 0.001) except FormLabs resin ( p > 0.05). For all 3D‐printed resins, the translucency increased, with increasing the post‐polymerization time ( p < 0.001) and 60‐ and 90‐min showed the highest translucency. For printing orientation, 90 and 45 degrees significantly showed high translucency in comparison to 0 degrees ( p < 0.001). FormLabs showed significantly higher translucency when compared with NextDent and ASIGA per respective printing orientation and post‐polymerization time. The translucency significantly decreased after thermal cycling for all tested resins ( p < 0.001).

Conclusion

The findings of this study demonstrated that the translucency of 3D‐printed resins is influenced by the printing orientation, post‐polymerization time, and resin type. As a result, choosing a resin type, and printing orientation, with a longer post‐polymerization time should be considered since it may improve the esthetic appearance of the 3D‐printed resins.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalPolymerizationDenture BasesAcrylic ResinsTime FactorsMaterials TestingDental MaterialsHumansColorSurface Properties

Stichwörter der Autor:innen

3D printingcomplete denturedental materialspolymerizationprinting parameterstranslucency

Substanzen

Acrylic ResinsDental Materials

Autor:innen und Institutionen

  • Department of Substitutive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • Department of Preventive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • Department of Dental Education, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • Department of Restorative Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • Department of Removable Prosthodontics, Faculty of Dental Medicine, Al-Azhar University, Assiut, Egypt.

ORCID-Profile: Mohammed M Gad, Shaimaa M Fouda, Ahmed Elakel, Essam A Nassar, Soban Q Khan, Ahmed M Rahoma, Mutlu Özcan, Fahad A Al-Harbi

Zitieren

APA

Gad, M. M., Fouda, S. M., Alshammary, H., Altayyar, R., Elakel, A., Nassar, E. A., Khan, S. Q., Rahoma, A. M., Elhagali, A. F., Özcan, M., & Al-Harbi, F. A. (2024). Influence of different printing orientations and post‐polymerization time on the translucency of three‐dimensional (3D) printed denture base resins. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13866

Vancouver

Gad MM, Fouda SM, Alshammary H, Altayyar R, Elakel A, Nassar EA, et al. Influence of different printing orientations and post‐polymerization time on the translucency of three‐dimensional (3D) printed denture base resins. Journal of Prosthodontics. 2024. doi:10.1111/jopr.13866

BibTeX
@article{Gad2024,
  author = {Gad, Mohammed M and Fouda, Shaimaa M and Alshammary, Hend and Altayyar, Raand and Elakel, Ahmed and Nassar, Essam A and Khan, Soban Q and Rahoma, Ahmed M and Elhagali, Ahmed Fathey and Özcan, Mutlu and Al-Harbi, Fahad A},
  title = {Influence of different printing orientations and post‐polymerization time on the translucency of three‐dimensional (3D) printed denture base resins},
  journal = {Journal of Prosthodontics},
  year = {2024},
  doi = {10.1111/jopr.13866}
}
Kostenlos starten →