EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The impact of print orientation on the fracture resistance and failure patterns of additively manufactured cobalt‐chromium post and cores

Ülkü Tuğba Kalyoncuoğlu iD, Simel Ayyıldız iD, Emine Odabasi Tezer iD

Journal of Prosthodontics · 2023

DOI: 10.1111/jopr.13762 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, 2023. Verfasst von Ülkü Tuğba Kalyoncuoğlu und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Gülhane Dentistry, University of Health Sciences Turkey, Ankara, Turkey. Hauptthemen laut MEDLINE: Chromium Alloys, Post and Core Technique, Dental Restoration Failure, Tooth Fractures. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The aim of this study was to evaluate the impact of the print orientation of direct metal laser sintering (DMLS) posts and cores on the fracture resistance and failure patterns of endodontically treated mandibular premolar teeth. Materials and Methods Sixty intact human mandibular premolars were endodontically treated. The teeth were then randomly divided into four groups ( n = 15). Cobalt‐chromium (Co‐Cr) metal posts were fabricated by traditional casting (Group C), and DMLS method in 0‐, 45‐, and 90‐degree print orientations (Group DMLS 0, Group DMLS 45, and Group DMLS 90). The posts and cores were cemented with composite resin cement and subjected to compression test at a crosshead speed of 1 mm/min. Data was analyzed by using one‐way analysis of variance ANOVA and multiple comparison post hoc Tukey tests ( α = 0.05). Specimens were viewed under a stereo microscope with x20 magnification to evaluate the fracture types.

Results

No significant differences were found among the groups tested in terms of fracture resistance ( p > 0.05). Group C and Group DMLS 0 group exhibited similar fracture patterns.

Conclusions

It is possible to produce post and core restorations with the DMLS technique and use them clinically. Print orientation did not influence the fracture resistance. However, fracture patterns were different. Group C outperformed all DMLS groups in terms of fracture patterns.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Chromium AlloysPost and Core TechniqueDental Restoration FailureTooth FracturesDental Prosthesis DesignHumansBicuspidDental Stress AnalysisMaterials Testing

Stichwörter der Autor:innen

3D printingCo-Crfracture resistancelaser sinteringpost and core

Substanzen

Chromium Alloys

Autor:innen und Institutionen

  • Department of Prosthodontics, Faculty of Gülhane Dentistry, University of Health Sciences Turkey, Ankara, Turkey.
  • University of Health Sciences Turkey, Medical Design Manufacturing Center, Ankara, Turkey.
  • Department of Endodontics, Faculty of Dentistry, Ankara University, Ankara, Turkey.

ORCID-Profile: Ülkü Tuğba Kalyoncuoğlu, Simel Ayyıldız, Emine Odabasi Tezer

Zitieren

APA

Kalyoncuoğlu, Ü. T., Ayyıldız, S., & Odabasi Tezer, E. (2023). The impact of print orientation on the fracture resistance and failure patterns of additively manufactured cobalt‐chromium post and cores. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13762

Vancouver

Kalyoncuoğlu ÜT, Ayyıldız S, Odabasi Tezer E. The impact of print orientation on the fracture resistance and failure patterns of additively manufactured cobalt‐chromium post and cores. Journal of Prosthodontics. 2023. doi:10.1111/jopr.13762

BibTeX
@article{Kalyoncuolu2023,
  author = {Kalyoncuoğlu, Ülkü Tuğba and Ayyıldız, Simel and Odabasi Tezer, Emine},
  title = {The impact of print orientation on the fracture resistance and failure patterns of additively manufactured cobalt‐chromium post and cores},
  journal = {Journal of Prosthodontics},
  year = {2023},
  doi = {10.1111/jopr.13762}
}
Kostenlos starten →