Effect of laser surface treatment on shear bond strength between polyetheretherketone and heat‐activated polymethylmethacrylate resin
Journal of Prosthodontics · 2024
DOI: 10.1111/jopr.13744 ↗Kurz gefasst
Vergleichsstudie in der Zeitschrift Journal of Prosthodontics, 2024. Verfasst von Ananda Deeban Kuttuva Balasubramanian Sivaprakash Babu und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, SRM Dental College, Chennai, Tamil Nadu, India. Hauptthemen laut MEDLINE: Benzophenones, Polyethylene Glycols, Ketones, Shear Strength. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 28 Literaturangaben.
Abstract (Originalsprache)
Purpose
To compare the shear bond strength between polyetheretherketone (PEEK) and heat activated polymethylmethacrylate (PMMA) resin after laser treatment. Materials and Methods A total of 128 PEEK discs were fabricated (10 mm diameter and 2 mm thickness) and allocated into two groups. Group 1 was subjected to surface treatment followed by thermal cycling for 5000 cycles and group 2 was subjected to surface treatment followed by thermal cycling for 10,000 cycles. Each group was further subdivided into four subgroups ( n = 16) which were: no surface treatment; primer treatment; acid etching; and laser surface treatment. PEEK was then bonded with PMMA resin using the conventional flasking technique. The shear bond strength was evaluated using a universal testing machine with a crosshead speed of 1 mm/min. Statistical analysis was done using one‐way ANOVA for comparing within groups, followed by Tukey HSD test. Student's T ‐test was done to evaluate between the two groups.
Results
In group 1, the highest shear bond strength was exhibited by the laser group (19.08 ± 0.16 MPa) followed by the acid etch group (14.84 ± 0.23 MPa), and the primer group (6.43 ± 0.20 MPa), while the least shear bond strength was observed in the no surface treatment group (4.98 ± 0.34 MPa) which was found to be significant ( p < 0.05). In group 2, the highest shear bond strength was observed in the laser group (18.21 ± 0.23 MPa) followed by the acid etch group (13.77 ± 0.48 MPa), and the primer group (6.04 ± 0.11 MPa), while the least shear bond strength was observed in no surface treatment group (4.35 ± 0.21 MPa) which was found to be significant ( p < 0.05).
Conclusion
The shear bond strength between PEEK and PMMA resin was highest for specimens that were surface treated with laser and followed by specimens treated with acid etching, primer application, and without surface treatment, respectively. Increasing thermal cycling from 5000 cycles to 10,000 cycles also reduced the bond strength.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Prosthodontics, SRM Dental College, Chennai, Tamil Nadu, India.
ORCID-Profile: Ananda Deeban Kuttuva Balasubramanian Sivaprakash Babu, Ahila Singaravel Chidambara Nathan, Muthu Kumar Balasubramanium
Zitieren
APA
Kuttuva Balasubramanian Sivaprakash Babu, A. D., Singaravel Chidambara Nathan, A., & Balasubramanium, M. K. (2024). Effect of laser surface treatment on shear bond strength between polyetheretherketone and heat‐activated polymethylmethacrylate resin. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13744
Vancouver
Kuttuva Balasubramanian Sivaprakash Babu AD, Singaravel Chidambara Nathan A, Balasubramanium MK. Effect of laser surface treatment on shear bond strength between polyetheretherketone and heat‐activated polymethylmethacrylate resin. Journal of Prosthodontics. 2024. doi:10.1111/jopr.13744
BibTeX
@article{KuttuvaBalasubramanianSivaprakashBabu2024,
author = {Kuttuva Balasubramanian Sivaprakash Babu, Ananda Deeban and Singaravel Chidambara Nathan, Ahila and Balasubramanium, Muthu Kumar},
title = {Effect of laser surface treatment on shear bond strength between polyetheretherketone and heat‐activated polymethylmethacrylate resin},
journal = {Journal of Prosthodontics},
year = {2024},
doi = {10.1111/jopr.13744}
}
EUVIMED