EUVIMEDEUVIMED entdecken
Crossref

Retention of titanium copings to implant‐supported fixed dental prostheses

Sieu Yien Chiam, Hsin Lin Lee, Armand E Bedrossian, Qianhui Xu, William Kuykendall, Anna Ren, Timothy A Hess iD, Van Ramos, Kwok-Hung Chung iD

Journal of Prosthodontics · 2024

DOI: 10.1111/jopr.13706 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, 2024. Verfasst von Sieu Yien Chiam und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Dentistry, Graduate Prosthodontics, School of Dentistry, University of Washington, Seattle, Washington, USA. Hauptthemen laut MEDLINE: Titanium, Dental Implants, Aluminum Silicates. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 34 Literaturangaben. Gefördert von: ACP Education Foundation Research Fellowship, Spencer Funds, Department of Restorative Dentistry.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The aim of this in vitro study was to assess the effects of using different cements and titanium copings designs on the retention of implant‐supported fixed dental prostheses (IFDPs) using a pull‐out test. Materials and Methods Fifty zirconia (ZirCAD; Ivoclar Vivadent) and 20 prepolymerized denture acrylic resin (AvaDent) rectangular (36 mm × 12 mm × 8 mm) specimens were milled to mimic the lower left segmental portion of the All‐on‐Four IFDPs. Cylindrical titanium copings (Variobase; Straumann) (V) were used in 2 prepolymerized denture acrylic resin groups ( n = 10) while conical titanium copings (Straumann) (C) were used as a control group for zirconia with 4 groups using cylindrical titanium copings. Before cementation, the outer surfaces of all titanium copings and the intaglio bonding surface of prosthetic specimens were airborne‐particle abraded. All specimens were cemented following the manufacturer's recommendations and instructions according to the experimental design. After artificial aging (5000 cycles of 5°C 55°C, dwelling time 20 s; 150 N, 1.5 Hz in a 37°C water bath), all specimens were subjected to retention force testing using a pull‐out test using a universal testing machine and a custom fixture with a crosshead speed 5 mm/min. Modes of failure were classified as Type 1, 2, or 3. Retention force values were analyzed by the t ‐test for the prepolymerized denture acrylic resin specimen groups, and 1‐way ANOVA and the Tukey test for the zirconia groups at α = 0.05.

Results

Mean and standard deviation retention force values varied from 101.1 ± 67.1 to 509.0 ± 65.2 N for the prepolymerized denture acrylic resin specimen groups. The zirconia groups ranged from 572.8 ± 274.7 to 1416.1 ± 258.0 N. There is no statistically significant difference in retention force values between V and C specimens cementing to zirconia with Panavia SA cement (Kuraray Noritake) ( p = 0.587). The retention forces and failure modes were influenced by the cement used ( p < 0.05). Modes of failure were predominantly Type 2 (mixed failure) and Type 1 (adhesive fracture from prosthetic materials) except for the quick‐set resin group (Type 3, adhesive failure from coping).

Conclusions

When bonding IFDPs onto titanium copings, quick‐set resin provided significantly higher retention force for prepolymerized denture acrylic resin prostheses. Conical and cylindrical titanium copings performed similarly when cemented to zirconia with Panavia SA cement under the same protocol. The stability of the bonded interface and retention forces between zirconia prostheses and titanium copings varied from the cement used.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

TitaniumDental ImplantsAluminum SilicatesDental CementsResin CementsZirconiumGlass Ionomer CementsAcrylic ResinsAdaptation, PsychologicalMaterials TestingDental Stress AnalysisDental Prosthesis RetentionSurface Properties

Stichwörter der Autor:innen

cementimplant‐supported fixed complete dental prosthesesprepolymerized denture acrylic resintitanium basezirconia

Substanzen

Quick-Setzirconium oxideTitaniumDental ImplantsDental CementsResin CementsZirconiumGlass Ionomer CementsAcrylic ResinsAluminum Silicates

Autor:innen und Institutionen

  • Department of Restorative Dentistry, Graduate Prosthodontics, School of Dentistry, University of Washington, Seattle, Washington, USA.
  • Department of Oral Health Science, School of Dentistry, University of Washington, Seattle, Washington, USA.
  • Department of Epidemiology, Columbia University Mailman School of Public Health, New York, New York, USA.
  • Mechanical Engineering Department, University of Washington, Seattle, Washington, USA.

ORCID-Profile: Timothy A Hess, Kwok-Hung Chung

Förderung

  • ACP Education Foundation Research Fellowship
  • Spencer Funds
  • Department of Restorative Dentistry
  • University of Washington

Zitieren

APA

Chiam, S. Y., Lee, H. L., Bedrossian, A. E., Xu, Q., Kuykendall, W., Ren, A., Hess, T. A., Ramos, V., & Chung, K. H. (2024). Retention of titanium copings to implant‐supported fixed dental prostheses. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13706

Vancouver

Chiam SY, Lee HL, Bedrossian AE, Xu Q, Kuykendall W, Ren A, et al. Retention of titanium copings to implant‐supported fixed dental prostheses. Journal of Prosthodontics. 2024. doi:10.1111/jopr.13706

BibTeX
@article{Chiam2024,
  author = {Chiam, Sieu Yien and Lee, Hsin Lin and Bedrossian, Armand E and Xu, Qianhui and Kuykendall, William and Ren, Anna and Hess, Timothy A and Ramos, Van and Chung, Kwok-Hung},
  title = {Retention of titanium copings to implant‐supported fixed dental prostheses},
  journal = {Journal of Prosthodontics},
  year = {2024},
  doi = {10.1111/jopr.13706}
}
Kostenlos starten →